Search results

  1. B

    MEP-802a “non runner”

    Small update. I’ve been through my first 5 gallons of fuel and it will take a good load so far. Using poor mans load banks. Some $20 space heaters from tractor supply.
  2. B

    current SF-97 turnaround times?

    So an update for those after me that may find this thread for an answer. I just received an email today from govplanet stating my title was shipped via fedex from California with tracking info. Will update when it arrives and see if it’s correct.
  3. B

    MEP-802a “non runner”

    Well, decided to run as is for now and see if it’ll loosen up some. I noticed with my light running for troubleshooting and repairs it was starting to wet stack. So I’m thinking that being a 2009 with 17hrs it definitely needs to be run and broke in some / loosened up before I tear. Into it. So...
  4. B

    MEP-802a “non runner”

    It’s definitely pressurized. You can feel it pushing against your finger if you place it over the dipstick hole. That and I don’t think there would be any oil left if I open my filler while running. I left it open once and it slung oil all over the door. But I can try it. when it comes to a...
  5. B

    MEP-802a “non runner”

    It’s definitely pressurized. You can feel it pushing against your finger if you place it over the dipstick hole. That and I don’t think there would be any oil left if I open my filler while running. I left it open once and it slung oil all over the door. But I can try it. when it comes to a...
  6. B

    MEP-802a “non runner”

    Well here’s a update I was hoping I wouldn’t have to do. But, it’s back to surging so tank pull it is. Next is the blow by is bad enough that it’s pushing oil past the dipstick and filler cap enough that it wets the battery. So starting this afternoon I’ll be pulling a lot of the sheet metal...
  7. B

    MEP-802a “non runner”

    I have no idea what someone was trying to accomplish but this cap was still attached to the radiator looking like this. They did a number on the neck too. I straightened the neck as best I could and got a new cap but it leaks still as it can’t seal well.
  8. B

    MEP-802a “non runner”

    Both of those solutions are on the list of to-do’s. On another note does anyone have a lead on where to obtain a replacement radiator for this unit?
  9. B

    MEP-802a “non runner”

    Well, had a small slot of free time before work this morning and.......it runs now no surge and holds 240v at 60hz steady and sounds good. I would post a video to share but not sure how to do it from my phone. Now, the solution to the surge was a plugged primary fuel filter so I’ll need to grab...
  10. B

    MEP-802a “non runner”

    Pulled the pumps today. One at the time of course as to monkey up the rack alignment. They looked relatively ok but shot some carb cleaner into the ports and up the spring and worked the levers. Also worked the sprung end on the table top up and down and seemed to not have any binding. Upon...
  11. B

    MEP-802a “non runner”

    So, have run it collectively run it about 20 mins total and changed the oil and filter 4 times in that span. I now have clean oil in the filter, on the stick and when I pull the fill cap. Also can see the orange-ish primer I think through the opening at the cap which So there’s a win........I...
  12. B

    MEP-802a “non runner”

    Oh, and some good news......I found the exhaust gasket for the enclosure down in the radiator opening with the top removed. Whoever was in this thing before just dropped stuff anywhere I guess.
  13. B

    MEP-802a “non runner”

    Well got fresh filters and fluids all in and hot batteries and managed to get it to turn over. No start though. The main switch will make it kick or turn over once then stop as will the fuel pump after a few seconds. Dead crank will crank as long as I hold it though. I have a return line leak...
  14. B

    MEP-802a “non runner”

    Yes I have turned it clockwise a few rotations
  15. B

    MEP-802a “non runner”

    Well the only light I have in the tunnel is that when I got to it at the yard they didn’t assemble the exhaust enclosure seal and spring correctly so the spring was holding the flap open and I can see water down in the muffler. I’ve rotated it by hand clockwise a couple rotations from the crank...
  16. B

    MEP-802a “non runner”

    Looking worse
  17. B

    MEP-802a “non runner”

    Maybe not, this don’t look good for not having fluids. Just the tip of the dipstick was showing. Maybe it’s from setting up and “sweating” from low oil in the case.
  18. B

    Canadian member here

    Welcome form Florida here!
  19. B

    84 1008 build.

    I had a 88 V30 Air Force truck that was a 6.2 and the sensor for the high idle in the passenger side of the engine shorted out internally causing it not to work. It that also killed all my dash gauges as well. Not sure if it causes your dash to do the same as it’s lights only. It’s a fairly...
  20. B

    No Start Issue Since Dying While Driving

    You have a fuel pressure delivery problem it sounds like. But the solenoid fuse is the outlier here that’s strange. Could still be possible though. Also make sure you don’t have corrosion on the wire under the insulation causing high resistance. Would it run better when the pump temp was cooler...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks