Search results

Chinese parts, either the fittings or the gun and components.

Following are some pictures of the cable end. I slpit the nut just to get it apart just because curiosity kills me. You can see on the nut that it is bent and has been split through the hex for a long time. You can also see that the nut is bent as well as the wedge. The wedge halves are bent...

I'll snap a pic tomorrow. The truck was a NG unit, new 1953, overhaul at TEAD in '73, delivered to NG sometime in '74, the Museum acquired it around '79-80. NG unit made it look nice, but FILLED it with Bondo. Pieces parts missing, the rear winch station clutch lever at the trans, vice, some...

This is what we have, didn't know about the different lay. I do have a p/n. I was going to try Memphis. I have not looked out back, there might be a winch or some cable just baking in the sun. I'll check that tomorrow.

I did look at those, and they requier a piece on the end of the cable to lock it in. There is a liquid that can be mixed and poured onto the socket. This will be a last resort. But thank you!

I have looked, Oshkosh doesn't have any, Eastern Surpluss has none, both show on their sites, but not in stock. Who else might have the rear winch socket? I did put up a parts wanted ad.

That is so funny! I actually searched for "Highway Products Incorporated" and, there IS a company, out of Or. named that, that manufacturers fuel transfer products! I contacted them, a very nice lady answered, we chatted, I sent 3 images off to her as well as a link to this thread, and she sent...

Wait, those tires are for compressed gas??!!

Dunno if I would trust the tires, they are checked pretty bad. This thing is 2 years younger than I am and I am sure the tires, bladders, whatever they are called are original! I can find nothing on this on the interwebs

Didn't know where this shoulda gone, "Other Aux Equip" or here, I chose the latter! Here are some pics of an M6 rolling gas trailer. All of the hoses are there, I believe it is complete, holds 1000 U.S. Gallons. We have no TM on is so I do not know if this required a pump to fill or extricate...

There is also a nice CAD wiring diagram here on SS, https://www.steelsoldiers.com/threads/peter-bogs-cad-deuce-schematic.3843/ As well as the number chart, https://www.steelsoldiers.com/threads/m35-wire-number-chart.61140/

I have seen this remote mounted in a small aluminum box on a firewall or metal inner fender. And people do make bushings to rebuild a worn distributor.

I have seen GM HEI components melded into Mopar electronic ign system. Lemme look.......

I was thinking the same thing, just make the line a bit longer to avoid kinks.

The blue plastic water jugs/barrels work fine, I stored my dieselgas concoction in them for years. If you have the room, the smaller the better. They can be stacked. 15 gallon drums are the largest I would go with if I were to do it again. They are haevy but can be moved with a hand truck. Any...

I never saw a resolve on it.

No need to bleed, the Bosch in lines are self bleeding and will start if they have a boosted fuel supply, just put the pedal to the wood. I do know the A2 has issues with the pick up and lines. Easy way to tell if it is an engine or chassis issue is to eliminate the chassis and pull fuel from a...

I might get in trouble for this, but here goes, We have set up a GoFundMe to try and help out with the hydraulics. https://gofund.me/e3241c6e If there are any issues with me putting this up, please contact me directly through conversations and I will personally remove the post

So, here's a bit of an update. It has been VERY wet out this way, so it has been a slow process, however, there is one full coat on the wrecker with the exception of the crane and inside the bed, the future hydraulic work is going to be a bit messy. All of the cab and bed panels have been...

I need some help! The lever for the rear winch clutch engage/disengage on the trans is AWOL. All of the images in the TMs here are dark so that I can't see what the lever looks like. If someone has a clear picture of the lever, maybe able to give me a OAL measurement, that would be greatly...