Search results

I'm stumped, about the only test I haven't checked is the cranking rpm, but it turns just as fast as my M1009. Can I have a bad injector pump if it runs fine after starting with ether? (Yeah I know). If I use ether it will start immediately and run all day, no problems. I have good fuel...

http://www.govplanet.com/jsp/s/item/705080?h=6-22 Holy crap, I bid 5 for it, but 22K???? It was minty but someone really got caught up in the bidding.

After replacing the glowplugs my 6.2 still is very hard starting cranking forever numerous times before it might start. I'm suspecting I'm losing prime after it sits overnight. Do I just crack an injector line? Thanks.

Finally got around to the last two glow plugs, the last one of course drivers side rear cylinder was the worst. I had 4 out of 8 swollen and thankfully I ordered the JJ&A glow plug tool, but it was still a nightmare being a contortionist. Anyway, I get the last one out and the tool and...

I'm losing prime, when I use the primer pump I'm getting fuel and air bubbles coming out of the top of this sensor and of course when I finally get the truck started. I looked in the Parts TM, it shows a plug instead of this electrical device. Anyone know what it does and what the part number...

Wondering how hot the glow plugs should get. I decided to check to see if I was getting juice to a random glow plug wire, so I took a wire off one of the existing glow plugs that I believe are all bad. I connected that wire to a new glow plug and held the threads to ground then had my wife turn...

I finally got the energy to change my glow plugs in my M1038, I pull the first one out, it's a 705 it has a round connection! I bought 8 new Bosch that have the spade connector I thought all glow plugs had! The wires and connectors look brand new, can i get spade contacts for the new plugs, or...

Any chance message storage can be increased? surely it doesn't take all that much space. I Don't like having to delete info I might want later from other users I've contacted.

I have at least one broken off, wondering if i can just replace the plastic buckle? I got my M1038 HMMWV today!!!!! Too dark for good photos.

Any clues as to what was mounted on the right quarter panel?

Like a dummy, I didn't even think about there being a difference when I bought them and had them shipped halfway across the country........ I see everything getting jacked up on prices and pull the trigger before I think too hard about it.

Want to install a dummy radio or lower priced/older radio but still appropriate for the vehicle in an HMMWV. Any suggestions?

Here's my soon to be newest acquisition, I'm pumped. 11K, 34,000 miles. Bummer it doesn't have troopseats I don't think.

I'm thinking about bidding on a HMMWV and make it road worthy whatever it needs, but want to know if the SF97 says anything about offroad use only or is that just the hold harmless agreement?

What are these straps on the 931/932 and what are these electrical connections for on a 923 NHC250 above the IP?

My 923 NHC-250 idles fine except when I use the hand throttle. I'll set it say at 900RPM, it will stay at 900 RPM for a minute or two and then start increasing rpm on it's own till it's screaming. Any idea what is causing this and the solution?

Wondering if there is particular places besides the fender mount that are standard for different M939 trucks?

Just saw a "2012" BMY 923A2 sold for $18,000 dollars on govplanet. I hope this guy collects on his ironclad guarantee.

An M35A3 on GL went for 13K!!!!! M936A2's from 10 to 16K M925A2's from 8K to 12.7K!!!!!! Everything else highly inflated compared to what I paid for them. 2 non running M1009's 2500-4K

I recently bought a Ibistek complete medium towbar kit and paid a premium AFAIC. I cannot figure out how the towbar can connect with a 5 ton, the ends are 90 degrees off of where it should be? I'm assuming the ends they come with are the proper feet?