Search results

Bell housing, clutch linkage bracket, and cast iron tail shaft housing ordered... :rolleyes:

Just a slight difference... good for reclaiming space for storage. Drilling holes today and laying things out... I think I got those holes where those directions said to. 😁. Something in the back of my mind keeps calling me with that big round hole... 🤔🔈 🇺🇸🇺🇸🥓🥓🥃🥃

They all suck!!! Put a Cummins in!!! :driver: :ROFLMAO::LOL:;) I'm sorry... I couldn't help myself... :shrugs::rolleyes::eek::deadhorse:aua

The directions for the flares say 1" on the front and the rear. I was closer to 1.5"... My truck actually is a little higher in the rear than it looks in that picture... but I'm still building out the back.

I put put some power to the fridge and worked on the countertop! I have a little plumbing to finish up for water but it’s something else to check off the list! 🙄 🇺🇸🇺🇸🥓🥓🥃🥃

Pretty much the same set up... you won't clear 37's without cutting.

Mike, the only issue I really had was the flange at the manifold. They required some grinding to seat properly on the doughnut do to the spacing of the studs in the manifold. This second kit took much less grinding than the first one so I can't say how much is needed. I reused some of the...

Super secret squirrel... it’s for a k20 with a 5.7. 🤫. It’s the 89003 kit.

Luck was on my side... 🤦‍♂️. Always check where those wires went that you shoved out of the way while doing your lift and painting! 24v+heat of exhaust pipe = exhaust leak! Still need the wires for the box as they will be utilized for a DC to DC charger. 24v arc welding results!!! Dynomax...

I started seeing a girl named Dana... axle seal replacement is under way. Both axle shafts got new u-joints. Despite being 36 years old they still turned freely and they argued about leaving their long time home. I also installed new slingers, spindle bearings, and new seals. Had I known I was...

ORD has come up with a resolution for that... with a M1008 it's probably less of an issue. I have one being delivered Monday or Tuesday... :) https://www.offroaddesign.com/crossover-steering-sway-bar-kit.html

I guess I never updated... its been installed for a while without issues.

I believe this may be enough info to push me over the edge... :driver:

When I ordered from ORD for my springs.... can't say for the shackle because I replaced it and it already went to the scrap yard. (GU38001-B) Greasable Bushing, Bolt, & Sleeve Kit for both spring eyes of GM Rear Springs - 1.75" and 1.5" eye sizes

With the opening cut for the sink it’s time for a faucet. Keeping it simple with a hand pump version. Sanded and applied three coats of Waterlox. The cutting board came with the sink so I'm refinishing it to match better... 🙄. 🇺🇸🇺🇸🥓🥓🥃🥃

Next project, making sawdust and some smoke... 😁. Putting off that front axle... 🙄. 🇺🇸🇺🇸🥓🥓🥃🥃

This is 4" tuff country springs, bushwacker flares and 37's...

I've logged some miles, 155 so far. I went out to French Creek State Park and took a couple now and before photos in the same parking lots... 🇺🇸🇺🇸🥓🥓🥃🥃

Back to some interior work. I’ve had the straps for a while but finally putting them to uses. Each one is rated at 350 lbs so they better hold the fridge in! Fits in nicely 👍. 🇺🇸🇺🇸🥓🥓🥃🥃

Stay well and we all look forward to updates!!! (y)