Search results

  1. Floridianson

    FL Expandable Van side lock wrench

    Just pay shipping. should fit in USPS small flat rate box so what ever it cost.
  2. Floridianson

    FMTV wiring schematic

    Has anyone been able to construct the whole down load or seen a complete one page schematic. I was never good at gig saw puzzles and my ADHD is not helping. I down loaded and printed then tried to assemble. I can get the main trunk ground line run out but the rest I am having trouble fitting...
  3. Floridianson

    Front axle two vent lines 1088

    OK I did look through some TM's I swear. I have two vent lines connected to the passenger side mid axle housing. I removed both and put some air to both. One I can hear the one and it seems to be right above the front axle just hard to see where it ends but is up in the frame. The other there is...
  4. Floridianson

    Crane drain

    Well changed out engine oil and filter. Changed out Both fuel filters and good grease job. Been playing catch up on hydraulic lines that seem to let go one after the other in a cascade effect. Three so far but I doubt it will stop there.
  5. Floridianson

    Extruded fender rubber

    I am guessing that the after market rubber trim for the fenders is extruded. Now the new rubber that just came in has a set to it that is backwards. Does this set happen when it is extruded or when they coil it up? The reason I ask and also saw a post about it is the way the new rubber came is...
  6. Floridianson

    Free points and condenser

    Ok same deal tell me what these two pieces of trim came off of. I do not know but same as the Oldsmobile hood ornament plane bought them at the flea market same time. Did something stupid and ordered points and condenser for my truck. They came in and I took off distributor cap to find I have up...
  7. Floridianson

    Oil pan drain plug free.

    Ok there are two plugs one for the bellhousing and one for the oil pan. The shorter is for the bell housing / fording so as not to hit the starter ring with the threads. Now mine came with the shorter one installed in the oil pan and not one for the bell housing. Mine someone used a bad ratchet...
  8. Floridianson

    Brake bleed alone.

    Not lucky enough or maybe unlucky enough to have a mate here at the house. So off to the ACE hardware to get one gallon sprayer., Had the 5/16 hose here and had to buy the fitting. 1/8 NPT to 5/16 hose barb. I unscrew the adjustable tip on the sprayer. The 5/16 hose will fit over what threads...
  9. Floridianson

    If it helps: Power Wagon Parts Source

    https://www.dodgepowerwagon.com/parts/index.php
  10. Floridianson

    Wheel cylinders

    Changing out one of my wheel cylinders on the M37 and this came up. Now the wheel cylinder that looks new and has no machining on the face where the copper washer would go is a New China wheel cylinder. The older one with rust is from my M37 and the new one was to be for the M37 but the machine...
  11. Floridianson

    Thanks John at Midwest Military

    Had a little problem and John made it right. Tanks
  12. Floridianson

    Inner bearing race number

    I am getting ready to put the front axle back together with new brakes and slave cylinders. Have the hubs off so I would like to make a inner hub seal installing tool using the inner bearing race. If someone would be so kind as to the race number I will order one and make my tool. Tanks
  13. Floridianson

    Distributor oil port.

    I down loaded the TM's I could find and Erick and I did go through them but I am the problem child here. OK the distributor has a port at the bottom and a flat blade plug. I saw nothing in the TM's or lube order about how often to oil. I put a little motor oil in the port and closed it up...
  14. Floridianson

    Thanks C&C Eqpt.

    Thanks to the people up at C&C equipment. I ordered my new AVM hubs for the M37 on this Monday and they came in today Wednesday. Good price and no over charging on the shipping through USPS.
  15. Floridianson

    Thanks soupermike in La.

    Took time out from his day to get me a pic and measurement off the floor of what the clutch peddle floor board stop plate looks like on the M37. Mine was missing. My name is not Smith and I doubt I could shoe a horse but a little heat and a little bendy bendy and looks good enough to me. It...
  16. Floridianson

    Steering box rubber line.

    At the end of the steering box where the horn wire comes out there was just a little piece of rubber hose there. How far did it run up the inner fender well? seems like it would only have been able to go half way up the inner firewall to the electric connection. I would think it was for fording...
  17. Floridianson

    What did you do to your M37 today?

    Per the help of member pjwest03 aka Harlan starting in on my one wire alternator upgrade. I still have a 16 /19 mm pully on order but things looking good so far. I am using all my stock brackets and as of now looks like I will need a shorter stock belt. Had to rework the alternator just a bit...
  18. Floridianson

    Passenger seat hold down.

    I have the little latch for the front. Was there something to hold the seat from sliding side to side when getting into the truck. I see nothing on the truck seat frame work or on the seat bottom that might hold it from going side to side. Not a big deal just wondering. Tanks
  19. Floridianson

    Just had too. M37

    Well told myself I was done and getting out of the OD got to have stuff. Problem was Clay Walker did to fine of a frame off restoration on this one to let it pass so now she is mine. 1954 so she is one year younger than me.
  20. Floridianson

    Thanks to Member SilverStates

    You adding more to what you owed. You were quoted $225.00 and you sent me $250. Some good people around here. Thank you sir.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks