Search results

  1. Daybreak

    Break-In oil for the low hour MEPS

    Go into any Deere dealer and have them order it. Nothing else needs to be done. They will get it in for you. They are a dealership. They might not even have sold any, but, they can get it in for the right price. Greenpartstore has nothing to do with Deere. It is a profit making enterprise which...
  2. Daybreak

    Break-In oil for the low hour MEPS

    Looks to be twice the price. John Deere Break-In Oil can be purchased at any Deere Dealer. Green Ag equipment, or Yellow Construction equipment, or even online.
  3. Daybreak

    A427A Load Bank GovPlanet

    The Essex A427 load bank fits nicely on a metal garden wagon.
  4. Daybreak

    Fixing up my MEP-803A"

    Here is a quick link shortcut for starting a thread here in Generators section Start Thread
  5. Daybreak

    Acquired a Military surplus load bank

    And since it is the single point ground on the A427 load bank, I keep the bonding strap in place connected on the generator. (Ground + Neutral) Note: When done using the load bank, keep the generator on and load bank on for a few minutes after with no load. Need to finish cooling down the panels.
  6. Daybreak

    MEP-803A No Start

    Howdy, Start in this thread, 2nd post has quick links to lots of stuff. 3rd post has links to the manuals and stuff. MEP-802A MEP-803A Filters and Parts | SteelSoldiers
  7. Daybreak

    Valence's M116A3 Mounted MEP-803A (10kw generator)

    For the canister fuel filter cup. The little top gasket can be held in place with a little grease. Make sure you also get it lined up in the slot all the way around before tightening up. Part of the power unit supplies (Trailer mounted genset) included a 90 degree fitting and hose for the oil...
  8. Daybreak

    MEP802A has Phase 3 power but no phase 1 power?

    Just STOP. You are making me and others really nervous. You are dealing with electricity. Make sure you have the unit properly grounded before moving on. Get accustomed to the terms for the unit. From what you have stated so far.... It sounds like a wire has chaffed from vibration and is making...
  9. Daybreak

    AMMPS MEP-1030 5KW Generator List of Part Numbers

    Time to bring this back to the top. More MEP-1030 are showing up in the world.
  10. Daybreak

    AMMPS MEP-1040 10KW Generator List of Part Numbers

    Time to bring this back to the top. More MEP-1040 are showing up in the world.
  11. Daybreak

    MEP1040 warning code

    Howdy, The info is here. The post just roll back farther and farther. AMMPS MEP-1040 10KW Generator List of Part Numbers Manuals Mep-1040/1041 AMMPS 10kw 6115-01-561-7455
  12. Daybreak

    MEP1040 warning code

    Howdy, hehehe. :cool: :rolleyes: :LOL::ROFLMAO: The emergency stop button is pushed in. :) You need to pull it out. And push the reset fault button, and start it up. The same thing happens to a MEP-802/3 The unit doesn't do anything when the emergency stop button is pushed in. The AMMPS...
  13. Daybreak

    MEP 803A shorted battery

    Howdy, Start here in this thread. Generator Forum Stickies. MEP-802A MEP-803A Filters and Parts The second post has quick links The third has the manuals needed, and links
  14. Daybreak

    Fixing up my MEP-803A"

    Howdy, They are both the same. It's just that the electroswitch is made of metal, and that is the only difference. Make sure you move over the diode jumper.
  15. Daybreak

    MEp-803A 3-wire connection to house not working and need power asap!

    Folks, he is using a old old school dryer plug. a neutral and 2 hots. He is back feeding a service panel. No, officially this should not be done. You would be better off attaching 4 wires to the service panel, dual-pole 50amp breaker. (ground, neutral, 120 hot, 120 hot) It is kinda scary that...
  16. Daybreak

    Fixing up my MEP-803A"

    You should search http://www.steelsoldiers.com/showthread.php?168569-MEP-8xx-S1-and-S6-switch-variations https://www.steelsoldiers.com/showthread.php?170926-MEP-802A-803A-S1-Master-Switch-Source-Electroswitch
  17. Daybreak

    Acquired a Military surplus load bank

    @Jestes1 Go back and look at the pictures for a 1 phase 120/240 wiring connection. You also use the 8 inch long copper strap to connect the 3 upper lugs. It is stored inside the cage next to the lugs. Acquired a Military surplus load bank | Page 3 | SteelSoldiers
  18. Daybreak

    MEP 802a - split phase connection

    Howdy, I think you are missing the point of having 120/240 supply to your cabin. Even setting up a simple service panel would be better. What do you have which will require a 30amp plug? You might even be better off with a spider box. A 50amp input plug, and multiple 20 duplex receptacle and 30...
  19. Daybreak

    803 Pre-heat run-away

    Pointer to MEP-8xx S1 and S6 switch variations | SteelSoldiers and MEP-802A/803A S1 Master Switch Source - Electroswitch | SteelSoldiers
  20. Daybreak

    Question about picking up mep802a with trailer from GP.

    Howdy, Go back to my post and read the threads. Anyway, the newer Silver Eagle/Schutt trailer LTT-TQG uses multi-volt LED lights. More trailer info and such can be found next door. Trailers | SteelSoldiers
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks