Search results

I was trying to get my doors and top on and it seemed impossible. This truck came with the top rails and the rear curtain along with the camper tarp. I have a new camo 4man top that I want to get on. I was wondering if the soldiers goofed on this in the field or am I doing something wrong? It...

Was looking for something to mount my g923 that I got for cheap and found a frame on eBay. I had my battery seat available since I am working on the truck and noticed that the bolts were an exact fit for the frame. Instead of kicking out an extra 200~400$ on a plastic chair, I went with this and...

Hello all, I am trying to get my hood lights done correctly. My hood wires were cut before the canister plugs. I got new canister plugs and a pair of 12469143 harnesses. Does anyone have a functional diagram of this harness? I have a parts diagram from the TM but that doesn’t help me Much. i am...

does anyone know what this is for? I am missing it on my tcase so I ordered it because i needed a min order of 20$. not sure what this does or what it is used for.

I know that it is improbable to get some gauge brackets since they are not sold separate from the gauges. Most likely these things are missing or broken Like mine. I had an idea to use mold maker from michaels and fiberglass resin i had laying around to try to replicate this. Here is what I got...

Hello, i am looking to see if there is more than one part number for Ubolts that ties in the front driveshaft to the transfer case. Here is what I ordered from ilminterprise from Humble Texas. This is the only part number that I could find from my TM. what I received looks like the photo...

I was looking in the dash and I saw that this looked loose. What is this? What does it do? Is it repairable or should I buy a new one? I liiked through the electronics section from my TM and couldn’t find it. what is the part number if I need to replace it. One of its wires is coded 399. Thanks

Hello, i was noticing that one side of my rails look lower. After removing the screws, it looks like there is a bushing and hole made from the factory. this is an issue for me because I have hard doors and it interferes with closing. Below are the left and right sides: are the holes...

I was wondering what was mounted in this hole in the rear passenger wheel well. Does anyone else have this? If so, what did you use it for?

Hello all, i am trying to figure out how to mount some harness mounts for the 80mph speedo. All I have is this from the TM is there another TM that provides details? I assume part 10 goes inside the dash to offset the resistor so the wires can fit better. I al looking for exact locations for...

Hello all, I have searched for what this wire is, but can’t find anything about it. Below are some photos: The list of military vehicle wire codes: The plate with 348 C code. View from the top behind the alternator. from the bottom far away: closer up close

Hello, Quick question. for this piece, is the nipple facing in or out? the TM just looks like a circle. I know it is mounted on the outside with the plate on the inside. Just need to validate the nipple direction. I am thinking in. thanks guys.

Hello all, It seems that the 2 connector plugs on my harness that plugs into the corner light harnesses has been cut off. Instead of replacing the harness, I was wondering if anyone had these off a broken ecv harness or had extras off an ecv hood they aquired. thanks.

Hello, I have an 06 m1165. The dash lights are both LEDs. Speedo has built in light. When I have the switch on, I only see the speedo on even when the garage is pitch black. When I pop of the 2 caps, I can see the LED glowing green but not bright. I understand the bulbs can be going out but...

Hello all, I don’t know much about this transfer case but i was wondering if the speedo gear needed to be greased or does the tcase oil keep it lubed? It is a new clean install so I don't have a reference to the old part. I took a peep inside the hole with a camera and it seems that there are...

The truck came without front brakes. I was able to get one side on by inserting one pad and squeezing the other one in by holding the caliper forward a bit. The driver side doesn’t have room in the front unfortunately. Has anyone installed a brake on an ecv with 12” solid rotors (Driver...

Hello, I am trying to figure out the proper part for the front coupler shaft that connects the front propeller shaft to the front diff. It is for an ECV m1165 12k (not the A1). The only part number I can find is the 12342620-1 in the TM. The AM general does not have the ECVs as compatible...