Search results

Installed new pulley on my 400amp alternator and still making noise. Is there a greaseable bearing in this or bearing that can be replaced? I have been looking for a 200 amp alternator but no luck under $600.

My M1151 has a wobbly clutch pully and its making horrible noise. I see a bearing listed for the 200amp alternator, but was wondering if the same bearing can be replaced on the 400amp alternator. Looking for a replacement the cheapest I could find was $461 at mac motors.

I installed front LED turn signals to match my back LED turn signals and they only work when I have the bulb removed from the turn signal indicator. I have even tried the trucklite bulb for the indicator and also swapped out the flasher unit to a solid state nartron box. I have gone back and...

I don't know if anyone saw this post. If anyone's looking for multiple units of Hmmvs's they are trying to wholesale the non runners from Texas and Kansas. Anyone want to split a 10 pack of non runners? [emoji1787]

I've slowly got almost all the pieces for a 80mph electronic speedo conversion. Have everything except transfer case electronic sender and what looks like a diode board. Has anyone installed the kit? And is the diode board necessary? I can't even find a PDF of the installation instructions from...

Picked this up cheap but think I'm missing the bumper lock. Does anyone know where you can get parts? I see Rico now makes the tire carrier.

Just bought a luverne brush guard for my m1151. Does anyone have installed pics? I'm looking for how the mounts were attached. Thanks!

After installing the rear hatch with new seal, it feels like it's catching on top of seal when I open. Is it just because it's a new seal or because I installed it wrong?

Does anyone have a picture they can share of the rear seatbelts in a M1151 or M1167? I can't find the part number for the slantback seatbelt bracket. The sponsons are different than the 10 series.

Trying to remove the hatch on the rear of my slant back and I can't seem to get the latches to open to remove it is there anything special?

Started with my new project of M1152 to M1167. Pulled all bolts on B Pillars and 4 front roof retaining bolts and rear 4 retaining bolts. Was surprised how light the roof is!

Finally the M1167 has been delivered. I will documenting my M1152 to M1167. I will be selling all the parts I don't need in the classifieds soon.

Some eye candy. Bought em all. I wish.

Have a Mep 802A that has power to receptacles. Only power to lugs when I hold up the contact switch. As soon as I let go the light goes off and no more power to lugs. K1 was replaced. Any suggestions?

I have a flying nun M1167 and want to keep the armored roof. I have attached the TM manual's turret assembly and it looks as if it uses two pieces of metal. The part numbers only bring up NSN information for one part and I can't find any listed for sale. The piece of metal that is between the...

While waiting on my M1167 that I won in December to get released, I'm contemplating if I use the parts I want for my M1152 or rebuild. The engine is complete and was sealed off with tape on all open areas. It is missing front hood, radiator, injection pump, AC compressor, power brake booster...

Picked up this non runner Mep 804a 15Kw non runner with 19hrs for $2100. A little magic and loose wire repair. Sold for $6500 two weeks ago!

I'm having an issue with the bowl fuel filter, not the spin on. I installed a new filter and O ring in the top housing and its leaking like crazy. I've looked at all the parts diagrams and have it installed the way they show in diagram. Am I missing something? Its as tight as I can get it...

Went to order a few things off AMgeneral and all the items have prices listed as 0 and all greyed out. I wonder if its a end of year deal.

Here in nw Indiana its been brutal with -30 wind chills and snow. Here are a few pics from I-65 in Merrillville, IN. Indiana National Guard called out to help.