Search results

So I bought a Plan B 4 man hard top, installed it but didn’t like the seat belt bump out things it came with so I decided to cover the holes and put in something else. Searched high and low and finally settled on 1/4 5x10 boat bunk mounts. With a little modification I installed one bracket and...

Installing some second row leather bucket seats from a 2015 Ford Explorer. They seem to fit well. Width measurement is about 19.5 inches and length is about 22 inches from rear to front of seat. Found them for about $145 each from local salvage yards. The slider rails are approx. 17 inches from...

So I inspected my Flexplate awhile ago and noticed some of the teeth were worn. Went to start my truck and herd it skipping on the teeth a little bit😬. Is there any easy way to change it out. Or some instructions to take it out. Truck is an M1152A1 6.5 turbo with the 480le. Thanks in advanced!

I was looking at some H1 tail light buckets to replace the Hmmwv buckets. Reasons why you say. The fact that it has the integrated reverse lights and the lights seem to be cheaper. Any pictures and experience would be greatly appreciated.

I have an AC question. My M1152A1 (2 man) has the AC condenser on the right rear fender and was wondering what it goes to. My assumption is that the compressor is driven by the serpentine belt then is condensed on the radiator under the hood. Is the fender condenser used for addition cooling...

Notice a data plate on one of my geared hubs. Does this mean that they were serviced at the same time or something along those lines?

Anyone know what a fair price is for a set of 4 up-armored doors with 5/8 glass would be. Found a set. Picture attached.

I have been trying to find the plastic bracket that secures my temp gauge to the instrument panel. I had bought one but it wasn’t the right size. Apparently there are different sizes. The one I need goes with the temp gauge with led over heat indicator. If these aren't sold as a separate piece...

Has anyone made their own grounding harness? From what I have read the grounding point for the turbo version of the grounding is diffrent? Looking to make my own but I don’t know where to ground it and the lug size. Was thinking of using 16 guage wire. Directions would be great!!!

Looking to paint the frame on my truck. There are some small spots of rust and looking to freshen up the whole thing. Any suggestions? Looking for a matte/satin finish. Any past experience?

I recently have been tinkering with my M1152A1 and noticed that the wastegate doesnt move. I have pulled on the little rod back and forth with a good amount of force and no movement. In addition, I don’t hear the thing whining or spooling, but it’s loud and possible can’t hear it. It doesn’t...

I think I have an issue with my TSU. The truck starts right up from a cold start. If you let it run for 10 or so minutes and shut it off and restart the wait light comes on for a second then goes out. I go to turn it on it turns over for a little bit then finally turns on. I’m assuming that...

So I noticed that my temp gauge did appear to be working on my M1152A1. I tested the gauge by unplugging the wire at sending unit and grounding it to the engine. This made the gauge go all the way up and the over heat led to come on. That led me to believe that the gauge was good and the sending...

Built a dog house for 6.5 turbo out of 1/8 aluminum (old street sign).

I have been searching for the correct size serpentine belt. The belt on the truck has no numbers on it to reference and internet search has left me with multiple sizes. -2007 M1152A1 SN:252865 -6.5 turbo - AM General A/C -200AMP generator Attached is a picture of the a/c compressor. All my...

My tachometer at idle jumps around. At idle it sits at 0 then it just jumps up to 500 Rpm then back to 0. This is without hitting the throttle. I have a video but can’t figure out how to attach it.

I have an M1152A1 with the 2 wire compressor. I noticed that the A/C is not working. The fan runs fine but no cold air. I looked at the clutch on the pulley and it’s not engaging. I attempted to test the voltage to the compressor but I didn’t yield any result. Also let it be know I have no idea...

I have been slowly looking at my wiring and notice my P41 wires are all chewed up. Any idea what they might go to? In addition my 348c wire is cut and I have no idea where it goes. Any help would be greatly appreciated.

So I bought a CDR valve that matched the one that was crushed up in the bed of the truck. My question is the one I bought and the one that was crushed don’t appear to have a deep water fording nipple on top? I have a 2007 M1152A1 6.5 turbo. I did notice that the turbo model CDR valve feeds into...

I am looking to identify a loose hose near the front differential. I traced it back to where the air filter housing is, but I’m not sure what it hooks up to down near the front diff. In addition I found a green wire that is cut. Not sure if anyone can help me figure out where theses things go...