Search results

Great Pocono Arms and Military show will be held Sept 25, 26, 27 at the Pocono Raceway in Pa. A 450 table gun show, in conjunction with a Military vehicle show and swap meet. Everything from Guns, Ammo to Tank Parts. Become a vendor or volunteer! Table Fee for gun show | $75.00 Number of...

Does anyone know where the reel light mounts in the bed of the M42?

I installed a new rear wiring harness on the M37 and all lights on the truck work correctly but I have no power to the trailer plug on the truck. I checked my M101 trailer by hooking it to my M35A2 and all the lights work correctly. So I check the ground and all splice connections and all is...

I'm looking for a M37 rear wiring harness CC1391395.

I got a NOS wiring harness with my M37 and pulled it out of the sealed box and it is in excellent condition but the more I looked at it something seems wrong. The one issue the distributor wire seems to be on the wrong side . The part number on the box is CC1269077. also had 7371055 on the...

I had a leaking seal on the rear differential on my 1953 M37. I dropped the drive shaft and removed the center seal. Can I just replace this seal? If so does anyone know a NAPA number for the seal. I ordered a few numbers listed on a few sites and none of these were correct. Thanks for the help.

Does anyone have a wiring diagram for a Mars signal siren 24v? The NSN number is 6350-00-283-9341. I have the foot switch for the siren.

I got this trailer for free and turned it into a mule hauler. It was a 1968 ENG-T field lubrication unit. .

Does anyone have a ENG-T3 lubrication trailer with the data plates intact? If so could you please post some pictures. Also if anyone knows what the M number for the trailer chassis would be. I know the FSN number for the chassis is 2330 897 9002. Thank you for all the help.

This show is always a blast but this year it featuring Military Vehicles.

I have a AM-598U and a PRC-10 radio setup with all the correct cables installed in my M35A2. i don't think it is currently working and would like to see if anyone can check this out and give me a hand. Radios are not not my thing but would love to get into them. Thanks

Well I'm not sure what we are going to do with this but I do remember working out of these as a 51B (carpentry and masonary MOS). I have the correct genset for this unit and would love to put it back to factory. It would make an outstand wood pellet bbq cooker but that would break my heart.

We use our MKT trailer for diffent fundraising events and finally found a nice hand washing station. This is a scrub sink used in the field hospitals. What I like about it is that it works off a foot pedal and supplies hot water. It also has a nice heavy duty case to pack it away. Let me know...

We picked-up the mkt on wednesday and here are some pictures.

This will be my new project for the winter months and I'm looking for advice on things that could be a problem. As far as I know this is a M274 dated Feb 1959. I have two four cylinder motors for this unit both have the Willys name on the header. One was rebuilt in 1965 and only has 14 hours...

I need help with some of the cable numbers for my AM-598U 1. Power cable from MX-7777 to the AM-598U 2. From RCVR on the AM-598U to the AUDIO on the PRC-10 3. From the AUX ANT to the base of my truck mount ANT picture below. 4. What power cable can I use from my MX-7777 to the batteries...

The Hanover Exchange club will set-up 3000 3 ft x 5ft American flag from Sept 09 till Sept 12 at West Manhiem Elementry school 2000 Baltimore Pike Hanover PA 17331. I will be setting up my display with my M35, GP small and all of my field gear. If anyone else is game let me know 717-577-6201...