Search results

On the M939 trucks attached to the Emergency Air Brake Release valve mounted on the instrument panel is a pressure switch that is connected to the safety control module. It controls the light on the panel in front of the driver to tell the driver the emergency brakes have been disabled. I need...

Where can I get kit number 57K0154 for my gauge cluster panel. This is all the mounting hardware to hold the plate to the dash. I think it is 4 screws, washers, clips, springs? Any info new or used. I have none just bolts and that is a PITA!

I need detailed intel on where the 2 air lines from the trolly brake handle get connected to the air system. I have an M816 and am adding the trolly brake but am not sure where to connect the 2 air lines. the TM does not go into detail so I need input from a M818 owner. Thanks

I am looking for a winter front for my M816. I bought one on eBay that was NOS in a sealed bag with all the hardware but it is not for the M809 series, I am not even sure what it is for now after trying it. It looks like it could be but nothing lines up, the hood hold downs are off and it is...

Ok, I have known about this glitch for awhile and just have not cared enough to post but here goes. If I ground the rivet holding the volt gauge n the dash(either side) the volt gauge will read battery voltage. Is this normal? The key does not have to be on or anything. I found this by...

I have an M816 with the Cummins and it has the cold start system with the hand pump in the cab. It leaks fuel all over when it is used. I disassembled it and there are 2 o-rings on the end which I will replace and there is a brass collar at the other end which acts like a packing nut so when...

The Pumpkin Run Car Show & Swap Meet in EHT NJ is this Saturday. Saturday is the Pumpkin Run Car Show at Flemmings in EHT. There will be hundreds of cars on display, a field of vendors that will have everything you never knew you needed, Military Trucks and equipment on display, a...

Well I am not real familiar on the older tanks but I have what I was told was an APU gen set from an old tank, maybe a Sherman. It has a 12vdc high and low charge and a 120vac and dc circuit with high and low charge. It is a single cylinder engine and has electric start by feeding 12v to the...

Since I have been running the M816 almost daily and need the 6x6 capability I have the interim drive shaft installed between the 2 read axles but as most of you know this makes it difficult sometimes to turn a corner as there is no differential in the drive line between the rears. I was...

10th ANNUAL PINE BARRENS CLEANUP at WHARTON STATE FOREST 10 YEARS!!!!!!!!!!!!!!!!!!!!!!! a DECADE!!!!!!!! Come and take part in the largest one-day volunteer event at Wharton State Forest in New Jersey. On Oct 23rd 2011 at 9:00 AM the 10th annual PINE BARRENS 4 WHEEL DRIVE...

Does anyone know where to get replacement fuel tank straps for the primary and secondary fuel tanks? Prefer new but used good is fine also.

Does anyone know what happens to the boom on the M816 if a hydraulic line blows? Yes I know oils everywhere but on my Civilian equipment they have lock valves that hold the cylinder in place if a line blows to prevent the entire load from dropping. Does the M816 have any lock valves in the...

10th ANNUAL PINE BARRENS CLEANUP at WHARTON STATE FOREST 10 YEARS!!!!!!!!!!!!!!!!!!!!!!! a DECADE!!!!!!!! Come and take part in the largest one-day volunteer event at Wharton State Forest in New Jersey. On Oct 23rd 2011 at 9:00 AM the 10th annual PINE BARRENS 4 WHEEL DRIVE...

Can anyone ID this genny. I just bought it from a local guy and it runs but I don't need it and want to sell it but some ID info and specs may help. It runs good but it looks older the the rest of my collection so it is kind of a misfit so I am looking for a new home for it.

I have a M44/530C fire truck in the shop and I suspect the head gasket is blown and need to do a compression test and leakdown test to be sure. I think it is blown between 2 cylinders because it runs very bad, blowing a ton of black smoke and is Huffing out the exhaust(Very weird sound) Anyway...

OK, so I see m816's for sale all over the net and sometimes on GL but GL also has XM816 wrecker? What is the difference from an M816 to an XM816?

I am looking for the screw/clip kit for the dash cluster of my 5 ton. I know it is listed as a kit in the 34p but cant seem to locate anything. Does anyone know where to get the screws and clips from? Mine are all missing.

OK So here is something i have not seen or heard of anyone looking for. I need a little bit more reach with the boom on the m816 so I was thinking of building a lib for the end of the boom that would pin on. I understand that it would lower the lifting cab but I don't need weight just height...

I think this is the correct spot for this as this is a factory option on the trucks and not really a mod. I have an M816 and it does not have the trolly brake setup for towing and I want to add it. I found an outlet for the correct handle/valve which is the same as the air valve for the rear...

OK, So I have searched eBay, Google and all the usual part sites with no luck. I need a replacement Tach Cable Strain Relief adapter part number 12357124 This is in the 34p-2 book and is required if you dont want to keep replacing the tach cable like I have. Any hints on where to look would...