Search results

Ok guys After I put my new a3 wheels on and ever since I've had a bad vibration at 2200+ rpm at 60mph when my tires were on stock deuce wheels I never had the vibration and could cruise at 63mph comfortably. I feel the vibration in the whole truck it feels like it's gonna shake apart but only at...

I hope I put this in the correct forum. So I wanted to share this with all of you here. My family and I lost our home during Hurricane Irma and have been staying with family until we got back on our feet. We finally found a place with 7Acs that needs a lot of work in Arkansas. So getting my...

Ok guys I'm having a problem getting the shoes to line up with the the upper brake adjustment cams. They are off by a 1/4" so won't adjust properly.

I figured I'd start the thread for this this year.

Ok guys I picked up a NOS 20k Garwood winch I plan on installing on my bobber. Here's a video of the winch. I am going to be looking for the Level wind assembly for it as well. I am looking for the TM for this winch as I need to swap sides for the pto hookup from the passenger side to driver's...

Ok gous I just got a nos A/C unit and the evaporator and some A/C lines. I did some reading on here to try to find some help with the install. I will need to source a compressor and make or find brackets for it. Here a video. https://youtu.be/3KXav60ijL8

I just wanted to give a big Thank you to Floridianson &vmy daughter got a great deal on a soft top and frame from him and my daughter helped navigate and both helped put the top on as it started to rain. Again Thank you both.

Ok guys I have been doing a lot of research and parts gathering for this setup. Heres what I have set up and the parts list. Aubrins Multimeter SYL-1813R-24 24v version,Ogrmar SSR-40DD 40A DC3-32V DC5-200V Solid State Relay with heat sink K type Thermo couple 800 Degrees C 3 meter cable, Good...

Trying to find the size of the hole n threads on the small on top of the intake elbow. This fitting fits it .thanks guys

Ok guys I just serviced my knuckles less than a year ago. I happen to check about 2 months later the rubber was already dry rotting,well fast forward to a couple of weeks ago one side has torn. I decided to make my own. I made one so far out of canvas drop cloth and dyed it. Here's the first...

OK fellas doing oil change and oil/fuel filters. I need the part numbers for the fuel filters. My primary fuel filter is the long style that is reusable but it needs replaced. I know I can get the others at Napa can I get this one there too. Thanks I couldn't find it the way I was searching.

OK fellas I finally got most of the repairs done . I put in a used fuel gauge looked almost new,NOS tach cable, new windshields, new clutch disc,bearing retainer,pilot bushing, throw out bearing,clutch pedal return spring,seats reupholstered and some various hardware. The truck runs and shifts...

I need a clutch pedal return spring. I was wondering if I could pick one up locally or use an alternative spring I can get locally. Thanks

Here's a video and some TM pics of what is needed. I found these pics RustyStud posted. https://youtu.be/G6oPVx2Khks

OK picked up 5 NOS wheels at the Mount Dora Show. I wanted to know what valve stems to get and can I get them at Napa? I wil be running my 14.00 20 NATO NDTs. The tires are around 10" wide. My rear hubs are already flipped. Any tips and or help would be greatly appreciated. I tried to search it...

I just ordered a bearing retainer with a seal machined into it today. I ordered it from M Series rebuild LLC. There was a hiccup on there part after I mailed them a money order today in regards to a core but they made it right. I will post an update after I receive the part. I still had issues...

I just got an M105a2 trailer with the sewing enclosure in it. I may have to change beds because my M105A3 bed is to narrow at the tail gate or extend it 7".I am not sure yet. Either way Bouncin Betty Knox is gonna have a hard top bed. This month makes six years I've owned her.

Here's a video of the drivers seat passenger seat will be ready by this weekend hopefully my friend did a beautiful job. https://youtu.be/NwERQ1JcJcM

I talked to someone on here a few years ago about a newer style bumper you can mount to the deuce. I can not remember for the life of me the make and model number to try to find one. Have seen it mounted on a deuce just can't remember where. Thanks in advance for any help.