Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.
My transfer is leaking and I have to replace the seal. I am looking for item 19 in figure 101.
TM -34P // NSN 5330-00-079-1919 // P/N 11601229 // Seal, Plain Encased; Yoke Rear
Is there any known source where I can buy one or any equivalent from the civilian market?
Hello Everybody,
From the manual TM -34P I can see two different u-joints for the Deuce used on the prop-shaft forward rear axel to rear rear axle and trans to front axle. I do not mean the bolted prop-shafts.
The lubrication fitting is either straight or in an angle. In my Deuce i've the one...
Hi,
Does anyone know of an inexpensive source or has a repair kit for the M35 LDS 427-2 engine? Complete kit with sleeve, piston, rings. Six needed.
There was a complete set of six on ebay sold for $350. Memphis Equipment is asking $311 ea. which is $1,866 in total.
P/N 5702644, NSN...
I need some help cleaning my data plates for the Garwood winch. I would like to make them readable again. Remove the old paint without destroying the original paint.
In the past I was able to remove paint from my plastic vehicle models with brake fluid. Would that work here too?
What are you...
I'm currently working on the vehicle cab and have a question about the routing of the handbrake cable. There is part 14 in the TM and I no longer know where to mount it. The hole pattern fits in the cab so that I could screw the plate on from below. But then I kink the handbrake cable...
Hi folks,
It is cold outside and I have here a multifuel space heater with a spark plug defect. The heater was made by Hunter, NSN 4520-00-114-1055.
The spark plug must be replaced.
My first thought was, to search for the part number. I tried to find the manual for the heater online by using...
Ulf uploaded in 2014 the TM 9-2320-242-34 (Direct Support, General Support and Maintenance Manual)
On page 1-9 there should be the wiring diagram for the tractor, engine compartment and carrier. Unfortunately these pages of the PDF are incomplete and don't show the complete picture.
Can...
Today I wanted to wash and prepare the Goat for an event we have here next weekend. 1st start the Goat. Nothing happened. No instruments, no starter, absolutely nothing.
So I took my M151 and the jump start cable. The goat starts immediately. But the instruments still don't work, the light...
I am in the middle of my M35A2 restoration. Where do I find the bolts for the propeller shafts? From the TM it is NSN 5306-00-752-1001, P/N 7521001.
Thanks a lot in advance for your hints,
Richard
I am still looking for the yoke assy P/N 11601566 (issue July 1976 TM -34P , figure 107, item 2). NOS or used is welcome.
Would be great you guys have one for me or can tell me a source in the USA.
Thanks for taking a look,
Richard
Last Saturday I drove 80 miles with the Goat. No problems. On Sunday, after 1.5 miles of driving, there was a noise which I never heard before. I stopped and made a walkaround. Nothing to see. Shafts okay, engine oil level okay, cooling water level okay. So I continued my drive - with no noise...
I got some new wiper arms and wiper blades for my Goat. Unfortunately I cannot use and install them. The former owner installed civil wiper motors which I cannot identify. But they are not M561 related.
Does somebody know, where I can find a wiper motor for the driver and passenger side? NOS or...
First I am not a guru in a vehicle's electricity. But I have a problem with my Goat where some help or a good advice might be very helpful.
This is the situation:
When I am on the brake pedal or setting the turn signal to the right, the bulb on the carrier's right hand (driver's side) is not...
Hi,
After repairing my Goat's brakes in 2014 I had some fun in driving it. This year a friend of mine made new brake shoe pins for my Goat, because I wasn't able to find some. So I had to open all six drums again. And on the left front axle I found - again - mud and rust in the brake drum :-( ...
Just went thru the manual section of this site and found two times the TM -20. Unfortunately both threads are not allowing to download anything.
I have a TM -20 here on my desk, but the electrical diagrams are incomplete. Seems to me somebody forgot to unfold them before pressing the Copy...
I had problems to get my wheel from the hub. Finally it happened and it was a little bit tricky. Thanks to Loctite :naner: which was helpful, too.
Now the question. From the -34P I can see that it should be a bolt with a ribbed shoulder. But mine isn't ribbed. How can I get the bolt (steel)...
This weekend I finished the tear-down process of my Deuce and a Half. After the engine and the gear box were moved away, I saw that the frame on the right is following a bow. The frame on the left side is straight. This brings me to the question whether my Deuce had an accident in the past or...
Search for a lever for my S-280 shelter
Hi, I am looking for a lever for my S-280 shelter. Any ideas where I can get one? Or does someone here has one (or two) for me?
Perhaps this has been asked earlier. Is there a good source where I can buy parts for the Gama Goat? Am looking for some parts because of a coming restoration project.
TIA, Richard
During my Deuce restoration project I found this. The cab was having a sheet of metal over another sheet of metal, two layers. Is this normal? Or was this the try to repair something? I removed the outer layer and the inner layer is not as worst as I expected. Further the inner sheet of metal is...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!