Search results

My son is in Japan and hasn't been able to get on all week Sent from my iPhone using Tapatalk

Anyone near Snellville GA with a CUCV willing to let me buy them lunch? My son blew the engine in my CUCV, I pulled the old one but deployed to Iraq before getting the replacement in. I am in the process of hooking up the donor engine but it has been a long time since I pulled the old one and...

I am looking at a M1008 in ST Louis if anyone in that area is interested in coming to the GA rally and could drive it down Ill pay for fuel and buy you a plane ticket back after the rally.

Want to bid on some seats but am in Afghanistan so can't unless I can find some one willing to pick them up. Thanks Dave

Any one have it? I tried the one in the TM section and it goes to a dead link/wont open. TM9-2320-324-14&P.pdf

Any of you Atlanta area members have any suggestions on where to source a Saginaw Model 710IH steering box? These boxes are generally found on International S-series trucks from 1975 to 1990. I just ordered the power steering kit from waterloo specialties and being new to the area am...

Got my swing away tire carrier/rear bumper put on from Tactical Armour Group outside Atlanta.

I just bought a Deuce and will be going to recover it on 6 Oct. If any one needs anything hauled between IL and GA I'd be happy to do it. Obviously I will have a lot more room coming south. Plan on attending the GA rally and can deliver there as long as the recovery goes smoothly

I know the first ten replies will be use the search function but I have been reading through posts for days and while there is a lot of great info on insurance I haven't found any on what plates people are running in GA. I have been leaning toward Antique plates as it seems GA is not as...

Built everything out of MDF and then carpeted it. The amps are in the center console, makes it easy to pull everything out. Over kill for a CUCV but a friend sold his Viper and gave me a deal on all the audio components in it.

Anyone have the TM for this radio? Just got one and know nothing about it.

Let me start this by saying that I have no experience with big trucks and very little mechanical experience. That being said I have spent days reading through old posts and following the steps in the TM's. I bought my truck in New Orleans from a private seller and drove it to Corpus Christi...

Ok I just got all the parts to put my gun ring on now I need to be able to get to it. I would like to take the hard top off and go to the soft top. I see from searching that GMA seems to be the place to get the top but cant find anything on where to get the hardware. I found a member on here...

I just bought a ring and legs in NC need to get it to TX anyone shipped one of these before? Who did you use? thanks

My M1009 runs fine for about 20-30 min but once it warms up it will rev really high before shifting from 2nd to 3rd or not shift out of 2nd at all. I have replaced all the vacuum lines and it did not cure it. I bought a vacuum gage and the vacuum pump is putting out the correct amount of...

Went to start my truck and nothing, jumped it and it started right up but no power to any of the guages, do I need a new alternator or could it be something else?

The rubber mat in my CUCV is worn out and after having a gallon of fuel additive spilled in it I tore it all out. Looking for comments from anyone that has had the inside sprayed with bedliner, did you do it all the way through? Start behind the drivers seat? How much off a difference did it...

Ok I have read countless post on AC in the M1009 but have not seen any comments on the kit offered by OD Iron. Has anyone done it? If so did you do anything to insulate the firewall? I have the arctic heater kit can it be made to fit?

I have been having problems with leaks for the last couple of weeks, finally decided it was beyond my abilities and took it to a radiator shop, they want $750 to recore it. I have found new ones from ERIK'S MILITARY AND INDUSTRIAL SURPLUS 25251 JACKRABBIT ACRES ESCONDIDO, CA 92026 for $680...

The vinyl cargo cover I have is off of a 5ton, has anyone cut one down to fit a deuce correctly?