Search results

My horn works ok other than the fact that the valve leaks enough to constantly actuate it. It is faint enough that it can be barely heard above the engine noise, just concerned if it fails any more I'll be driving down the road at full blast annoying everyone around. I pulled the valve assembly...

I'm losing air pressure through the valve on the bottom of my air dryer. I pulled the rubber 90 degree boot on the bottom to gain access, and can push the valve closed to build pressure. when the pressure periodically relieves, the valve sticks open again. I searched all over, wondering if...

I am looking for a set of these brackets. They sold several huge lot of these recently at GP, I'm sure the winners of them would love to sell a set but I have no idea how to get in touch with them. Anyone have any leads? Long shot I know! NSN 5340-01-606-0202

My speedo shows nearly double my true speed. Not a huge issue in my mind but the odometer is running away at the same rate. Does anyone know what the issue might be? Can it be re calibrated electronically or mechanically somehow? Thanks guys!

This is a post I made elsewhere just now, but see this might be a more appropriate place to put it...

I found the bedsides, wondering if anyone would be willing to part with a tailgate. Thanks guys!

I finally got my EUC cleared, truck delivered. I only drove it a short distance to put it in my hangar until I get it insured. Man, I am so impressed with the condition and the truck itself! I have had 3 5 tons and the overall look and feel of this thing is amazing. I would ultimately like to...

I seem to have a small leak from my transfer case at the flange around the opening where the rear drive shaft enters the case. I had a mechanic rebuild my transmission and it works great now but before I bring it back for the leak..... any thoughts on a cause or fix? The mechanic also reported...

Something that should be so easy never seems to be! I bought a reproduction 1919 pintle to attach the fake M2HB to my MK64 cradle. It wont drop low enough for the spring loaded lock to engage the lathed grooves in the cone shaped tail of the pintle. All it needs is perhaps 1/8 inch and it would...

Just a quick question for folks with a cupola and shield setup, ... ever had any law enforcement issues driving around in public? I just installed a setup, only drive my truck enough to keep the systems working. I am not the kind of guy that drives around aggressively looking for attention but I...

Hello and thanks for the help. I have a 2 man 998 that I want restored. I have a slant back that I bought fairly restored, and brought it up quite a bit to original standards. I travel for work and spend enough time away from family that when I am home don't want to be a stranger working out in...

I searched the forum, got some good reading in but have a strange symptom with the trans and truck is disabled. I have the old school 3 speed 3L80.I will do some troubleshooting but maybe someone can narrow down my search. I was driving the truck and it started slowing while the rpm's...

So I am wondering if the replacement of a new parking brake is an easy bolt off and on proposition or is it a pita? I have the old style and it is a little beat without the safety release button. I would like to slap a new one in, but I already have plenty of projects on this thing that will...

I want to mount a coupla to the turret I still need to install. I think I have most of the parts, but will see as I go. I downloaded all the TM's I can find to get the turret installed, but not sure how the coupla mounts to the turret. I have the older style hatch with the two appendages...

I have a deep water fording kit and want to install vent louvers on my left slant back sponson. I wont get to the exhaust for a bit, but it looks like I might have to mount the louvers far enough forward that they may run underneath the pipe. The louvers stick out a bit less than an inch from...

Hello, I have 2 HMMWV's I would like to restore. Both won't take too much to do, and I have gotten most of the parts I need. I have done some work myself but have time constraints with work and sometimes need extra help. I am brand new to the area so no real contacts yet. My next project is to...

I bought a new solenoid to replace one that was inop. It is the solenoid that allows the engine to start (I took it off and have been overriding it with the emergency shutoff handle in the cab). I threw the new one on (Chinese part) and it worked a few minutes until it went up in heat and smoke...

Ok, so I bid on a 6 ton that I won, didn't think it through. Still very excited though. I want to fly into the nearest airport (Ontario I guess, but anywhere Southwest flies). I plan to try to drive this thing back to Phoenix. Is there anyone near a Southwest Airlines served city that knows...