Search results

I have a 2008 1165A1 HMMWV and wanted to check/lub if needed my ENGINE FAN GEARBOX? I have not beeen able to find the fan gearbox plug or reservoir? According to the manual photo it is part of the fan assembly, under the fan itself? Any help would be appreciated. Thanks!

When first starting the engine, the rpm's pulsate on the engine and electrical system for approx. 1-1 1/2 minutes than goes to normal? When this occurs my headlights, signals , etc. all fluctuate in addition to the engine. After this stops, the engine & electrical system appears to work fine. I...

I have a 1165A1 and attempting to getting my wiper washer pump operating. The pump was unassembled during armor de mill. Looking at what diagrams I have seen it appears there should be two wire connectors under the dash near where the pump/reservoir tank are located? I have not been able...

Hello, I have purchased a Warn Series 18 winch that was advertised as for a Humvee. I have found they usually install the series 12 in the Humvees. The series 18 is a little longer (26.51") where the series 12 is 26.25". Can anyone tell me how much frame clearance they have with the Warn...

Hello, I have just purchased a 2007 HMMWV M1165A1 and waiting for delivery. It currently has a hardtop with flat turret included. It has no doors and apparently the armor has been taken off. I have been advised the actual up-armored flat doors will not work as the rear sides are flat. My...

Hello All, I have purchased a new steering wheel and horn buttom (wire attached). It looks like a newer style wheel but fits onto the spline properly. The horn button wire appears that it would go straight down the tube. I can not find any exit hole/slot on the steering tube. Can anyone...

Hello, Can anyone tell me what the specs/clearences are the intake and exhaust valves of a 451 engine? Thanks for your help. Dennis

I just reinstalled my GAZ engine and transmission. After getting the engine and trans bolted down I went to install my transmission Fork Handle and can not remember exactly how it went back in?? Inside the top area of the trans. I see a double hard wire type part crossing over the area where...

Hello All, Went to attempt to lift my cab. It went up approx. half way and had to use the cab manual jack to lift rest of way up. My manual says to check the hydra. reservoir but the diagram they show does not appear to match my truck? I also noticed the manual says: "If Equiped"? I would...

Hello, I have been having a problem with my UAZ469 4 cylinder overhead valve engine not getting any oil to the rocket arms. I had just installed a new Fram oil filter and have been told there are two types of oil filters. One is a "Full Flow" and the other "By Pass flow". Does anyone know...

Hello All, I have what I believe to be an UAZ 469 newer replacement overhead valve engine on my 1955 GAZ. I had just replaced the head gasket as I had some water getting into my oil. After replacing the new head gasket I noticed that I was NOT getting any lubrication up onto my rocket arms...

I BELIEVE I AM HAVING A PROBLEM WITH MY K1 RELAY ON MY PDB, M1078). I HAVE A FULL CHARGE ON THE BATTERIES AND WHEN GOING TO START MY PUSH BUTTON STARTER SWITCH JUST CLICKS. I WAS ABLE TO PULL THE K1 RELAY AND USED A JUMPER WIRE ON THE TWO VERTICAL PINS (NORTH/SOUTH) AND IT TURNED OVER AND...

Hello, I found that my Ether Canister was empty and purchased a new Ether can through Napa Auto Parts. Does anyone know if the threads are different than the military stock number as I am having trouble screwing it down. Thanks for your help. Dennis

Hello all. My 1994 m1078 has been dead in the water for over a month now. I had replaced the batteries a couple of months ago and it was working fine with no problems. Last time i used it was at a holiday parade and returned home, parking it. Went back out 3-4 days later and nothing. Not a...