Search results

Complete spare tire mount from an M923A1 military truck. It is very good condition and was taken off of a rebuilt truck several years ago. It was in dry storage until very recently. It comes with the supporting brackets that bolt to the frame, as well as one of the spare tire clamps shown in...

Winch setup for M809 5-ton military trucks. Includes: front winch with good cable, chain and hook, frame extensions, a dual output (dump truck style) PTO, a front driveshaft, and cab lever and linkage. Possible full or partial trade for clean, rust free CUCV or civilian 8' square body bed or...

This is my LAST NOS M103-A3 Military Generator Trailer Vinyl Cover. It fits the 1.5-ton military generator power plant trailers, which are based on the M103 chassis. One such trailer is shown in the pics and is similar to the M105A2 cargo trailer. The typical military generator power plant...

I got this bed to use as a bridge over my stream. While stripping it down, I noticed that there were some holes in the bed that did not go through to the bottom. On closer inspection, it appears that the stock bed floor has 4 panels ( that are approximately 1.5" thick ) on it that are fully...

Can any of you guys tell me what this marvelous little mystery part is/does? The dotted line part inside the red circle. I have not dug through every page of every manual yet, but I thought it was interesting that this is the only part on this drawing in the -34P without a number. Even the...

Does anyone know the model and/or use for these Autocar tractors? Crismon doesn't seem to mention them. The first pic is of two that sold out of APG years ago on GL, and the second is a pic I found somewhere online.

Can anyone provide me with some pics and accurate dimensions for the rear outrigger plates? Material thickness, hole diameters, etc... The TM does not seem to indicate that they are the same as the fronts, but they are the same as the boom jack feet. Or, if anyone knows where I could locate a...

Does anyone know if the PTO cover plate from an M809 transmission is the same size and bolt pattern as the one on the Allison MT654 in the M939 trucks? Without looking, I think they are both 6-bolt, and I assume they would be some SAE standard size. But, you know what happens when you ASSume...

Would anyone who is near Scranton (Lake Ariel, to be specific) be able to pick up some M1028 shelter brackets in the next few weeks and hold onto them until the Gilbert show in September? I'm glad to pay for fuel & time. If so, please PM me. Thanks!

Number of threads in classifieds I'm guessing this option has always been set to it's default for me, and probably for most everyone else. I really don't spend much time in the individual forums, unless I'm creating a post, so I never noticed it. However, given our new classified arrangement...

OK, so I got a BUNCH of these in with some stuff I bought a while ago. I could never figure out exactly what they were, although the NSN referenced a Bradley, so that was my only guess. Tonight, I took these pics to post pics here and ask if anyone knew what they were. Then, I saw this...

Does anyone know if the starter from the NHC-250 in the M939 will work on the 400 Cummins in the M916/M920? Given the transmissions are vastly different, I kind of doubt it, but does anyone know for sure? Thanks!

Anybody know a source for new M818 data weight & dimension plates? I looked at MV Data Plates, Saturn and a couple of the other usual suspects, but could not find anyone with tractor plates. Anybody know who might have them? Thanks!

Does anyone have one of the 600 gallon fuel pods that they could take some measurements from? Specifically, I am looking for the measurement between the skids on each end, the width of the skids (or a measerment from outside to outside of the skids), the overall height of the skids when sitting...

I always get a kick out of this. It's sort of along the lines of the "Ran when parked" story, but not exactly. I like when GL says "Unknown Running Condition" and then includes pics of the trucks freshly "windowed" block.:cookoo: Of course, the first pic might explain the second. Who was...

If anyone has these items or knows who might (locally), please let me know. I am looking for the following: -Complete M1009 tailgate (the usual rust is OK) OR a window handle (with lock cylinder) and tailgate glass -Complete passenger side door -One tailgate side latch and bolts (part that...

As much as I hate to sell it, I really don't get enough use out of this trailer and I have some other projects to commit funds to. Here's the specs: 1989 Kasel Mfg. Company M101A2 A few surface rust marks, but absolutely NO ROT! No dents or damage. Tires are very good. New GMA 3-color vinyl...

Anybody have a clean M1028 bed with tie-downs for sale in the MD/PA area? Did anyone win any M1028s at Meade that they will be making a flat bed out of?

My father and I should have some parts at Aberdeen for sale. He might also have his M211 for sale. Anybody need anything specific? Here's the short list of the bigger stuff I think we'll be bringing... 6 - M135 Wheels/tires 1 - Exhaust system (I think it is complete) 1 - Engine (runs well -...

Has anyone done the conversion using the civvy controller as outlined in the Technical article written by 85-M1028? 85-M1028, can you check the part number on your wiring harness? I ordered the part number stated in the article (#15306187) and it is definitely not a GP relay harness. I played...