Search results

Anyone have any idea if a M105a2 will ride good behind a M923a2 on 53's? Worried about height difference between trailer and pintle.

This will be a little long. Please bare with me. Equipment status...starwheel all the way to motor, that other screw is turned out some. The fuel adjustment on the back of the pump is turned up some. All of this was from previous tinkering and things have been excellent other than throttle...

Been around HMMWV's since early 90's and dont remember a high pitched whine coming from the motor. Not like this. The sound it in the video if you can weed through the normal rattling shitbox sounds. I have a squeak up front from what I think is the idler and I thought this was from that but...

On my 2001 M1097a2, 6.5....after recovery of it non-running I replaced or put on a new alt, ps pump, both top idler pulleys, water pump, and new belt. Now I have a belt squeak that I can not find. The intermittent squeak does change with RPM. I have the belt off now and there is no squeal with...

Trying to find out what kind of insulation is in the floor of a shelter. Closed foam? Will it dry out?

Been without power since about 2100 yesterday. Been using the MEP about 5 hrs at a time. Besides having to be careful not having the hot water heater on same time as the clothes dryer, I am keeping a decent load on it but not even at 75% Got this one out of Albany when they were selling them...

Just wondering if there is any way to save one of my headlights that flickers sometimes. Was most of the way off just now. I like the look but expensive.

I am about to have to do alot of rewiring on the deuce. What is the best source and I do mean least expensive for the prestolite wire and male/female comnectors?

I bought this truck as a parts truck and it has ended up being something I will not be parting out. It had a corroded wire #10, from magnetic relay that I had to repair to get it started. Figured I would eventually have more wiring issues. It sat down near the beach for a long time...

I just cant find some decent pics of a nice M923a2 with an S-280 in the back. If anyone has some, please post. Kicking around getting a shelter.

Cant scratch the paint off easy enough to see the NSN. Anyone able to ID it by look or that serial#?. The other piece does not have a visible nsn. Just trying to see if this is one of later boxes or not.

Took the M1097A2 on a road for first time and have an issue with the tires bouncing from time to time and steering wheel doing the shuttering back and forth. Comes and goes and figure it may be due to the tires sitting in one spot for probably a few years. Only other real issue I found was a...

Been doing a few things to this M1097A2 since recovery....water pump, ps pump, and a few other things along the way. Today was my first chance at getting under it and doing a good stem to stern inspection of the underside. Besides a cracked dust boot, all is really good then I came to the mid...

The truck has the demilled DWF kit and I will get it back together. My 1990 M998 had its sensor cup on a frame rail I believe. I understand the newer models have it mounted more up front. Anyone have a pic of where they are located now? This M1097a2 was rebuilt in 2014 in case it matters.

Dealing with an alternator that someone gave me. it has a different pulley than the one I have that is bad. I was able to pull the pulley off of the one that came off my M1097a2, to put on the newly acquired one but cant get the pulley off. The 3 jaw puller won't fit behind it. Before I get...

Could someone please direct me to the thread that showed how to make the plastic gauges clear again? Cant find it. I am assuming using something like the headlight cover polisher.

Looking for correct size fitting to snap onto the fan clutch Q/D so I can line up to access the bolts. I have a compressor to put air in but none of my fittings will snap on. Any suggestions?

On a 6.5 NA, non remote reservoir pump. Has anyone been able to source a pump local? Looking at pumps and seeing alot that are very very close but not exact part number.

Starting to get to know my new MV. Have replaced the fluids and have gotten the engine back together. Bought it with no alternator or PS pump on it and as a non-runner. Installed a pump and alternator and it cranks and drives ok. The alternator is loud, assume its bearings are about...

Newly recovered M1097A2...going through the motions of swapping fluids and filters. Bought as non-running hmmwv, alternator and PS pump are off if it. I put some batteries in it and it fired right up with just a few seconds of erratic oil pressure bouncing and then leveled right off. I did not...