Search results

Here is one for the M37 experts. While on a trip to the Philippines, I ran across this MV that I think is an M37 hauling a load of concrete from the harbor to an inland construction site. As you can see the truck suffered a flat rear tire, we came by a couple hours later and the crew was...

The wife and I spent a couple months in the Philippines visiting family and friends for the first time in 4 years and took some pics of the Philippine Army Base on Siquijor Island. The Army has replaced their M715 trucks with the newer KIA KM 450 trucks. There are at this time no longer any...

This Unique Mighty Mite belongs to one of our MVCC members. When Mark found it, it was in a very forlorn condition. It didn't run and the original 4-cylinder air cooled engine had been replaced by a cast iron 4-cylinder Volvo engine. Necessitating the grill being extended out about 6 inches to...

I couldn't find much on this subject in the archives, so I thought I'd ask the membership. In the 17 years that I have owned this truck, this is the only dash component that I haven't replaced or removed. It's the long handle switch right above the 3-lever light switch. Is there anything I need...

Some pictures from the MVCC Spring Meet. April 27-May 1.

This is a Jeep Steering Linkage Kit (2530-735-1411). Are any of our Jeep Gurus familiar with this Kit. Is it applicable for the MB, GPW, M38, & M38A1 jeeps. Here are several pics of the boxes, and the parts to the kit. I have a 1953 M38A1, and I would like to rebuild the front end this summer...

TM 10-5411-205-23P

I'm still learning my way around the M38A1. My Jeep is running great, but she has a rear main seal leak. Guys, can I replace the rear main seal with the engine in the Jeep, or do I have to pull the engine??..............thanks!!

I purchased a 1953 M38A1 awhile back. It had a Carter YF carburetor when I purchased it, the YF is standard on commercial jeep F head engines. My YF leaked a little, and ran a little rough. So I found a Carter YS 950 at one of the California meets, and had it rebuilt by a competent carb shop. So...

About 8 minutes of Russian Trucks In The Rough, In The Water And Elsewhere. These Guys would have fun at the Georgia Rally.

This is a little long at 23:48, and there is no audio, but there are sub titles for every picture. But if your interested in Gun Trucks and the brave crews that manned them, this is for you. There are about 100 Gun Trucks shown here. Some Gun Trucks were built on M51 dumpers, and at 16:20 Proud...

This is meant to be an appendix to Papa Bears fine detailed post on Gun Trucks. Some of the trucks in PBs post you'll see here, along with the men that served.

I looked in the archives, and couldn't find this exact question. I am going to be changing all 10 tires on my M35A2, and I would like to go with the larger diameter 11.00X20 NDCC tires to keep the original look, and pick up a couple miles an hour top end. I know the tires will fit on the rims...

Many Thanks to Guyfang, Chris Miggins, and Robo McDuff for their unselfish time spent digging up TMs for a 1977 MAN 4X4 5 Ton truck. The TMs are of course printed in German, and search as we might, we were unable to find any in English. After some head scratching, we did find a company that...

This will be my first pick up at Doyle Storage. Anything I should be aware of? Address is Doyle Storage 448-460 Simms Rd. Doyle, CA 96109. On the map it's not to far from the Sierra Army Depot....Thanks.

Is Bobs ARMY/NAVY Store in Mojave, CA. still open? I've been by several times over the last several months usually on a Saturday and he's been closed. Out back there's a couple of trailers and an M38 left, just about everything else outside is gone.

More to come.

There are quite a few posts in the archives on this subject, and I read through quite a few of them, and watched a few You Tube vids as well, before coming up with this idea. As with others who posted on the subject of front bumper tow bar mounts, one of my main reasons was to get the 100+ pound...

Couldn't find this issue in the archives. I'm installing a new companion flange and output shaft seals in my transmission. (pic is the old one) The TM calls out for a torque setting of 120-150ft lbs. To get a gap in the castle nut to line up with the cotter key hole in the main shaft, I have to...