Search results

Special delivery new NOS Genhead replacement....... Now just a lot of verifying before install. Cause for replacement , Is failed to drive disc, stator failure [emoji2955] Sent from my SM-G975U using Tapatalk

Looking for information on this model truck, any input would be greatly helpful, in terms of the Ins and outs of the PTO or hydraulic system. Thank you Sent from my SM-G975U using Tapatalk

Does anyone here own one of these and no the insane outs. Thank you Sent from my SM-G975U using Tapatalk

Asking who has seen different size shims on this starter for the 6.2 diesel. I seen someone pulled one off of a 6.2 civilian type engine and that shim was probably a .150 thousands. Thank you to everybody that might have some information. Sent from my SM-G975U using Tapatalk

I know the NSN and part numbers for the thermostat on these units. does anybody know the heat range that they are? Is are they consistent or are there variations. Thank you Sent from my SM-G975U using Tapatalk

Looking for information / and diagrams for this injection pump is injection pump sea pic Thank you Sent from my SM-G975U using Tapatalk

Any thoughts, preferences Or opinions on this matter Would be appreciated. Thanks JC Sent from my SM-G975U using Tapatalk

Ok, lower mount bolt ....... Is this a inherent problem????? Sent from my SM-J337U using Tapatalk

Looking for pictures of mounting of the rear maintenance Box to the frame/chassis of this truck. Any pictures will be helpful. Thank you, Sent from my SM-G975U using Tapatalk

Do a little clean up on electrical. Have a frozen spinning nut circled in picture. After disassembly I think this was the cause for starter replacement by previous owner. Sent from my SM-G975U using Tapatalk

Well just finished passenger side return lines with new, IMO I don't care for the cloth outer cover as it makes it difficult to see if hose is all the way on. Also looks so so with fraying. A few pictures new and old. Hope they don't leak. Thank you Sent from my SM-G975U using Tapatalk

Just received a new glow plug control module (card) From previous conversations It was said NOT to Rely on TM wiring diagram as shown. As it shows resistor feed wire and small Orange wire coming from gpcm both connected together on gp solenoid large post. I do not want to damage the new...

New to me D30 Having some wiring issues on the solenoid. I've attached to pictures 1st picture showing how mines wired up 2nd picture showing the TM. So by looking at the TM the small Orange wire in this picture that's on the bottom large post ( with the other larger orange wires going two...

Breaking them out and testing them up....... Sent from my SM-G975U using Tapatalk

Just fired off my Gen. Set for the 1st time load tested 3 phase 110/ 208. can only get about 5.9 amps on each leg before it starts to droop down ?? any thoughts Thank you Sent from my SM-G975U using Tapatalk

This unit was at a work place. Delivered no fuel, oils. Drained etc. After oiling up, fueling, new batteries priming systems, tried to fire up. Not luck not even a burp or hint off starting. Techs cranked and cranked and more almost running all battery charge out. Fuel to injector pump and to...

June 1st getting ready checking out the bank and load testing. Sent from my SM-G975U using Tapatalk

Looking for anyone's thoughts or opinions based on these two different units in terms of functionality and configuration and durability. Thank you, Sent from my SAMSUNG-SGH-I317 using Tapatalk

Hi, I'm looking to add a remote fuel tank around 150 gallons. Any recommendations for how and what to use for the line connection? The tank is designed for a transfer type pump (all fittings on top) but I planned to pipe it directly to either the remote fuel pump or the main fuel line pump...

Finished my Nato slave jumper hookup for charger, working great.