Search results

I need to settle a disagreement. Is there any load limit configuration that exceeds: 5000 lbs for LMTV 10,000 lbs for FMTV ?? How much does the bed weigh? Thanks

Black rubber chunk. Has fresh break on one side. Has a radius( guessing about 12".) Its not tire. Has a 90 degree corner to the radius. The radius side has some old grease and road gunk. Parked the truck 4 days ago after driving into the creek to fill my water tank. Got in today. It wouldn't go...

Morning again, Where do I buy the terminal pins (rd M & F) and the spade connectors for the connector blocks in the LMTV/FMTV? I have several circuits that dead end at one side of a J/P connector. I wish to add a wire/pin to the other side and continue the circuit. Ex. The work light circuit...

Every where I will use my LMTV will be past the boonedocks. Mostly cuz that is where I live. I'm a 65 year female. I need all the mechanical leverage I can think of. I bought a 1" impact for the lug nuts. You say How will you run it? The truck can supply all the air I need. I have 2)-30 ft...

Getting ready to install a LED Light bar on my LMTV. The question is were to put it? Go high? Go low? Is there any real advantage to putting on top of the cab? My main concern is most off road will be in the woods. I had to trim all the trees just on my drive cuz they beating up my...

Several people I know and myself have bought the visor upgrade. Only to find the brackets for the standard cab are missing. After getting no response from the seller I was going figure out how to use the airdrop cab brackets. Which I have. I have a detailed instructions and pictures if you are...

When they demilitarized my truck they completely stripped the panel of any CBs and relays when they took out the radios etc. And damaged a few more. Best place to get more?

I have a FMTV wiring diagram. But it’s mostly worthless. I am retired avionics. Complex wire schematics and diagrams were a everyday job. This thing is worthlessness. I am thinking I have a partial incomplete. I have tried the TM here but I get this goofy error message that I done have enough...

1999 LMTV All lights flash on the CTIS. I followed the manual to reset. Doesn't help. Guy on YouTube replaced the pressure switch on side of wet tank. Seemed to fix his. But didn't mention the PN or where he got it. I found the manual reference to change that switch. Can't seem to find a PN.

The Fire Dept has a 1970 Kaiser 5 ton. Needed to replace the wiper blades before they destroy the windshield. Does anyone have a source or suggestions?

Garwood 20,000 lb winch. Need left hand roller guide bracket. The TM 55-2320-211-15-1 shows' the steel bracket as 7409804-1. For those that followed my escapade on the cable tangle... Wait.. there's more... Still cleaning up previous damage done to our winch. When I was under the truck...

Our volunteer fire dept has a 1990 Kaiser M54A2 converted to a tanker. Using the winch has been a issue. Mostly because we don't know what we are doing. Finally got the PTO to engage. Then had difficulty getting the lever in front to work. We had the cable pulled out. Then once we got the...

Good morning from the Ozarks. I have a 1999 M1078 with a dump conversion for working my ranch were everything is 4WD. I would like to put a tank and pump on a pallet that could be dropped on to the bed for a fire. I already have a very portable gas "firepump" on a big hand dolly. It has 300 ft...

Please add me to the Arkansas area

That 2 air duct from the heater box goes through the box to left that has the trailer/ parking brake valves. The plumbing to the valves completely squashes the air duct. I am in the middle of replacing the parking brake valve. My thoughts is while its now accessable to remove the duct. use the...

Need a complete working display