• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

NVAM998's latest activity

  • NVAM998
    NVAM998 replied to the thread Keyed Switch.
    I went the keyed route from fed mil parts. The first one had loose terminals. They replaced it. The second one with fairly little use...
  • NVAM998
    NVAM998 reacted to Mainsail's post in the thread Keyed Switch with Like Like.
    I used a keyed switch that merely interrupts the neutral safety switch. The stock start switch is retained in place, and the keyed...
  • NVAM998
    NVAM998 reacted to cdohner44mag's post in the thread Keyed Switch with Like Like.
    Can a keyed switch be used to interrupt the 24v feed to the factory switch? That way if the factory switch happened to be toggled when...
  • NVAM998
    NVAM998 reacted to juanprado's post in the thread Keyed Switch with Like Like.
    My low tech solution is to leave it in gear when I shut down.........
  • NVAM998
    NVAM998 posted the thread The Goat Locker in Trailers.
    Made a ramp and put these guys out. They like hanging out underneath. Didn't chew the light wires. Just fooling around.
    • Goat Locker.jpg
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    OK, so I have a lot on my plate and maybe I'm an idiot. I had installed am XM381 trailer converter for a commercial 12 V trailer...
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    Interesting. It was with the Guard then a PD and I've been undoing their 12 mess. Maybe they put one in. With my tinnitus it will be...
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    Hi, Yes they were. I tried adjusting the switch, then disconnected it and ohmed it out. Seemed good, but wouldn't work. When I...
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    Yes, switch is "bad." Multimeter says it is good but it must not be good under load because it won't trip the relay for the brake...
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    Yes, either stop or service, now my brake lights are on unless I press the pedal. Confused. Guess adding the troop seats messed up the...
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    Too strange, I drove the other day and noticed that my brake lights are on unless I press the pedal, in which case they go out. I think...
  • NVAM998
    NVAM998 reacted to Mainsail's post in the thread LED replacement no flashing with Like Like.
    After changing to all LEDs I have the following: With the switch in STOP LIGHT everything works as normal; turn signals flash as they...
  • NVAM998
    NVAM998 replied to the thread 12 or 24 volt system.
    Not hijacking but I have a M998 that is stock 24 V and was reading the TM 9-2320-280-20-1 for fluids capacity and noticed on page 1-32...
  • NVAM998
    NVAM998 replied to the thread LED replacement no flashing.
    I haven't tried that yet, I think...
  • NVAM998
    NVAM998 reacted to Just1More's post in the thread LED replacement no flashing with Like Like.
    This amazon bulb worked in my signal switch: https://a.co/d/3t62iFe
Show older items
108,877members
164,040threads
2,307,948posts
1,063online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks