Recent content by BadAmish

@LuckeyD - Thank you for all your knowledge and help. I think I have the red dip switches in the correct positions. Here is a photo: I am still trying to figure out the 3665 fault code / error. I do not think there is a short after digging into the wiring harnesses and the wire that is...

@FarmingSmallKubota - Our's is missing, but @Guyfang set us up with a PDF we didn't have so we are grateful. The good news is that our control panel looks new inside: I removed the screen thinking that the crud was on the inside but it turns out the crud is not on the inside or outside...

@Guyfang - OK, I guess you mean let's start at the beginning and work through it. Reminds me of this: https://freemusicarchive.org/music/Learning_Music/An_End_Like_This/01_Learning_Music_Music_Part_I/

@Guyfang - Thank you, I did not have that one. Everything helps! I looked on all the doors again just now and nothing. In TM 9-6115-751-10 it implies that the label would be on one of the document boxes on the inside of the doors but mine does not have it. I also did not see any hopes where...

@Guyfang - I have been looking for a schematic / wiring diagram and all I found was in the TM 9-6115-751-10 in the form of a label. I cannot find this label on my generator unless it is installed under a panel I need to remove. Is there any other wiring schematic that will help me track...

@peapvp & @Guyfang - Thank you. I was able to spend some time last evening looking into the wiring and control panel. Here are some photos of what I found: The wire that we've been referring to as burned appears on closer inspection to be gnawed or chewed and / or possible just rough-handled...

@peapvp - Thank you for your reply. Do you mean I should test all wiring before reconnecting this cut / broken wire shown in my above photos? Do you think this cut / broken wire could be the reason I have the 3665 fault code?

I haven't been able to work on our MEP-1050 for a while and the new air cleaner housing came a few days ago and I was able to get that mounted this morning before the sun heats up. The new air cleaner housing came with a filter element cartridge so the one I bought from Amazon will be a spare...

@Guyfang - Cool, thank you. I've been on some boards where they get upset when one strays off the topic. Still waiting on that air cleaner housing. We are having a heatwave here lately and some other stuff has taken priority but I hope to get back into working on this unit soon. I think I...

@Guyfang - Ok, and Thank you. Sometimes I feel impatient to get this unit running, but I want to do it right and not break it any more than it already may be. The banjo bolt, seal/washers and filter element arrived but am waiting on the new air cleaner housing. UPS says it is stuck somewhere...

@Guyfang - I used this one: MEP AMMPS 1050 -24 24P Manual small @Guyfang - Yes, that helps a lot, thank you. @Guyfang - I did not try looking through that manual as I thought I needed the "MEP AMMPS 1050 -24 24P Manual small" which I think is the same as "TM_9-6115-751-24P". I did save the...

@2Pbfeet - Thank you. Did you find it in the manual? If so, can you tell me which page?

I'm having trouble locating a part that was lost in shipping. It is the NATO slave receptacle cap shown in this photo: I searched the manual you folks provided but did not see it mentioned, or maybe I missed it?

@peapvp - Roger that. What did they used to say - "It's not a job, it's an adventure". Of course I'd like to get this bad boy running, but I also have to confess that I am enjoying learning and working on it. If it wasn't so hot out there lately I'd have more updates to share. It also seems...

@peapvp - Yes, your screen looks exactly like mine - Oil Pressure greyed out also 3664 & 3664 errors. I imagine that the old pressure sensor is on the engine somewhere and connects to the control panel. If your control panel is showing the 3665 fault code because it is not connected to the...