• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Recent content by catienla

  1. C

    MEP004 low voltage

    I think sometimes my mind is my worst enemy. I have been running this unit on two leads voltage at 220 vac since 2011, maybe this is why all my problems started. I knew it was 208 v but it did not register. When it produced 220-230 v this is what I used. I think I created my own problems. I'll...
  2. C

    MEP004 low voltage

    L1 to ground 87 volts, L2 to ground 87 volts, L3 to ground 87 volts. Across L1 and L3 154 volts.
  3. C

    MEP004 low voltage

    MEP004 producing 87 volts on all three phases. Was 125 volts last time I ran it. Regulator rebuilt relay box repaired. Any ideas?
  4. C

    mep004 reads 0 phase to phase 480 phase to ground

    I'm just thankful someone has the patience to try and teach and old dog new tricks.
  5. C

    mep004 reads 0 phase to phase 480 phase to ground

    I am producing power 130vac at breaker box. Thank you guys again for your help. Would be in the dark without you. Now I am going to start on an 8kw with antifreeze in the oil pan. Thanks again. Mike
  6. C

    mep004 reads 0 phase to phase 480 phase to ground

    Thanks for the confidence booster but I think there is a long row to hoe to get even close to the knowledge you guys have. I do enjoy learning though. Board is in relay box, will install box and check F1 and F2 in the morning. If there is nothing else to test before start up I'll try it tomorrow...
  7. C

    mep004 reads 0 phase to phase 480 phase to ground

    A5 tested good using TM. Soldered traces with a solid copper 20-22 ga. wire. Reinstall?
  8. C

    mep004 reads 0 phase to phase 480 phase to ground

  9. C

    mep004 reads 0 phase to phase 480 phase to ground

    Got it. Internet is spotty. Having trouble connecting, if you don't hear back quickly. Thanks, Mike
  10. C

    mep004 reads 0 phase to phase 480 phase to ground

    Started to do test and in reading the procedure some of it includes #2 and #15 terminals. These are the ones the traces are burnt. Should I just do a partial test or solder a wire to replace burnt traces? Is test done with A5 out of relay box and unwired or with box hooked to gen set as it would...
  11. C

    mep004 reads 0 phase to phase 480 phase to ground

    Also have TM5-6115-464-34
  12. C

    mep004 reads 0 phase to phase 480 phase to ground

    Can I download the TM to a zip drive and have it printed? Don't have service where gen set is, have to go back and forth from computer to generator. I have a manual TM9-6115-464-12 is this sufficient?
  13. C

    mep004 reads 0 phase to phase 480 phase to ground

    I will use TM and check A5 tomorrow. Thanks
  14. C

    mep004 reads 0 phase to phase 480 phase to ground

  15. C

    mep004 reads 0 phase to phase 480 phase to ground

    I remember the switch terminal coming off and replacing the switch, my memory of the events that followed the switch were buying the aftermarket AVDR and not being able to get it to work. You contacted me and walked me through the process of building the ugly but functional circuit board on a...
See more
112,353members
166,076threads
2,338,681posts
1,145online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks