Recent content by CPDOG

  1. CPDOG

    M170 EMERGENCY BRAKE HANDLE/LEVER

    HELLO PARROTTT, you are welcome., good luck with your jeep.
  2. CPDOG

    M170 EMERGENCY BRAKE HANDLE/LEVER

    NDT, that is correct, this what we were trying actually see in the pic you sent, it still hid in there, but once we compared the piece we had to the pic, we knew what was going on with it at that point.
  3. CPDOG

    M170 EMERGENCY BRAKE HANDLE/LEVER

    hello jason, thank you! i will follow up with that one, please give me a few days as there are several measurements involved and i will throw in the pics too. i am attaching a few now from when i was doing their fit ups after replacing the aft end of the jeep.,
  4. CPDOG

    M170 EMERGENCY BRAKE HANDLE/LEVER

    UPDATE to our question concerning the M170 Medical Jeep Hand-Brake: we are just following up with some closure so it may assist in the future to someone on this site,, again thank you for looking and the participation. we looked in numerous areas for a clear picture of the e-brake install for...
  5. CPDOG

    m170spare tire mount and bar

    hello! thank you for responding, very cool mod, i am going to look into it as well.
  6. CPDOG

    M170 EMERGENCY BRAKE HANDLE/LEVER

    ndt, thank you for the pics and POC.
  7. CPDOG

    M170 EMERGENCY BRAKE HANDLE/LEVER

    HELLO FELLAS, we are in the middle of a full blown resto-mod of a 1962 M170 jeep. does anybody have a picture (even one) of the e-brake handle installed in a M170 jeep? i know this sounds really mundane, but we have searched extensively for a clear picture of it installed. if anyone has this...
  8. CPDOG

    m170spare tire mount and bar

    hello parrattt was that kinda of a kit there? please share some part numbers for the material if you have them available....thanks!!!
  9. CPDOG

    1991 m923a2 electrical charging issue

    Hey there sorry for the late reply hey when I tested my box there was a procedure in the tech manual and it spells it out over like to two sections and it goes over step-by-step and including using a voltmeter on testing it that’s a procedure i used I don’t have a tech manual in front of me...
  10. CPDOG

    m170spare tire mount and bar

    Hello jason You are correct on the reply issues. Be sure to share your m170 , these are hard individuals to play with, so all tricks / ideas are most welcome
  11. CPDOG

    m170spare tire mount and bar

    hello again Jason, ok all tubes for seats, front support bar on dash for litter, tire mount bars and the bow rails are all 1" tubing, this time i am loading pics from home computer vice the phone so i believe we will have a more success this time. also i found another site with the tire mount...
  12. CPDOG

    m170spare tire mount and bar

    Jason I will look at those tonight and get back with you repost pics too, I didn’t know you were looking for any measurements initially, talk again soon
  13. CPDOG

    m170spare tire mount and bar

    Hello Jason I did find a guy who made these but when I got it was off by 3” on each end and the height was off by 1 1/2 “. So cut it in 3 areas to fix the length and replaced the 2 center pieces with taller ones, after that it fits very nicely, I have attached pics for you too. This M170 is a...
  14. CPDOG

    What have you done to your JEEP today

    hello there!! yep new concrete added last year and she (my little drama queen) is a golden retriever and you know who owns that garage too, I am just a renter!
  15. CPDOG

    What have you done to your JEEP today

    hello all, haven't been on in awhile. i have been busy with our restoration of our 1962 M170. it was used on the flight line at a local air base and we bought it from a fellow miltary vehicle restoration club member. as you can see it got down and dirty. we had to even replace a few...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks