Recent content by Towbarman

Guyfang I was looking at my work order and it states that it is a PU802. That's what's on the data plate also, but on the Generator it self does show it as a MEP804B. It does have the new Quad Mod. installed. The fuse is good, replaced it with another that I did check twice. The test I was...

Ray70 Yes it is trailer mounted. Yes looking through the PU 802 reference really sucks. I've been working on this thing for a while now. Almost 70 hrs. Boss ain't happen. Thanks again. Towbarman Out.

I have a PU 802 generator. Looking for the 2 wires off the voltage regulator to use to magnetism the exciter. The interrupter does not stay on when you hit the switch. The needle moves just a little when the master switch is turned to run for 2-3 seconds and the interrupter little goes out when...

Guyfang My apologizes for jumping into that thread. It sounded like the same thing going on with my gen. Again, I do apologize.

I have taken a reading on my Alternator regulator. Any help here. OHMS VAC 1. 6.2 1. 2.8 2. 4.7 2. 2.9 3. 4.7 3. 2.7 4. -4.7 4. 11.2 5. -.51 5. 11.3 6. 4.7 6. 2.6 7.1.5...

I'm trying to do the same thing. One of my steps was to unscrew P6 from J6. I have a PU 802A generator that when I hold the main switch it shows 120 volts and 60 Hz. When I release the switch to let it run voltage goes down same as the Hz

Good morning!! I'm looking for a BI-Annual Service Work sheet for a M1075 Palletize Load System. I have found Annual & Semi Annual, which both are different services. Would be appreciated a Bunch. Towbarman

I tried to find an NSN for the door and handle for the MEP 802A. The part number is wrong. The door handle doesn't come up with right NSN or Part number. The number I have for the Door is: P/N 88-20198, Handle: NSN 5340-01-379-0893, P/N S79SDTXXSXXXX. Never seen a part number like that one. Any...

Afternoon One of my coworkers has an issue with a MEP 802A generator. He describes it like this. Cranking and starting but half the gauges not working. Pulled voltage relay, checked, swapped. Now generator will crank but no start. He rechecked all the other relays, all are good. Any help be...

Good morning gentlemen. I say that loosely of course. I'm reporting back on my issue with the rear markers and the middle rear marker lights. It has been a hassle chasing wires. I stared from the back where the markers are. I checked the power of course, taillights work, 4 ways work, but still...

Good morning My issue is, I have power to my headlights, turn signals and front amber lights. I have rear taillights and blinkers, but no power to the rear red marker light. I took my multimeter to check for power and nothing. Checked breakers seems to be okay. What is my problem. Thanks, TowBarman

Good afternoon Towbar here again for another question to ask. On our service sheet, it has service the 2 air tank check valves and the front emergency gladhand check valve. I know I have units that don't drain their air tanks after they drive them. When I go out and check the tanks, moisture...

As of right now the truck does pull either way , and the steering wheel is waaaayyyyyyy off center too. I'll probably be the one doing the string test due to the young mechanics I have working here. Thanks for information.

Needing some information/ good advice on how to do a wheel alignment on a 5ton M1083A1P2 cargo. Unit wants it to drive straight with the steering wheel in the right position. Thanks Towbarman

Morning to yall I have a M1151 with coolant in the transfer case. What would cause this to happen. I only know this issue from my mechanic/ inspector. My thought was to change out the T-Case instead of the transmission or would it best to change both out. Not sure how long the fluid has been...