Recent content by Wingnut13

  1. W

    What is the CAT part number for 3116 fuel primer?

    Excellent news! I’d much rather fix than replace. I wasn’t sure if it was possible as the primer bulb is crimped on. Good to know the check valve parts aren’t under that. Thanks
  2. W

    What is the CAT part number for 3116 fuel primer?

    Thanks for the part number. My pumps check valve has failed, when I try and drain the sediment bowl the fuel drains back to the tank….
  3. W

    What have you done to your FMTV or LMTV today

    Double shot…. Too quick on the trigger.
  4. W

    What have you done to your FMTV or LMTV today

    I was able to put a few hours together to work on big truck. I got the PTO installed on the transmission. It took a bit longer than two hours. I dropped the front driveshaft for clearance, though I’m sure the PTO wouldn’t fit otherwise. Removed the cover plate, used some gasket remover to get...
  5. W

    What have you done to your FMTV or LMTV today

    I guess I should add that the order of parts is the -an *90 fitting, debris screen ( had to pick it out and reshape after) 1/8’ hex set screw (has a hole all the way through for fluid flow) spring, then the check ball, second spring. One thing I will add is when reassembling the parts don’t...
  6. W

    What have you done to your FMTV or LMTV today

    Finally got into my OE spare tire lift cylinder. It had locked up just a after I got the truck and would not move. I had replaced it with a commercial cylinder, no internal safety locks, and it wouldn’t quite lower the tire all the way. I had saved the original and got some time to look into it...
  7. W

    What have you done to your FMTV or LMTV today

    Yeah I was wondering if you were heading this way. You may be able to just flip the pumpkins over to reverse your direction? But the issue with that would be driveline angles get worse…. Maybe? I’m not close to a truck to look.
  8. W

    GREASE GUN

    Never seen that…. Sweet
  9. W

    What have you done to your FMTV or LMTV today

    Mag drills are the best, and now with centerless cutters they are the berries. How about putting another steer axle in the rear?
  10. W

    Small 24 volt winches for LMHC

    I’d venture to guess you could run a 12v winch on 24v without much issue…. If I was to catch up on projects a bit I’d try it.
  11. W

    What have you done to your FMTV or LMTV today

    Yeah I purchased a mostly complete kit, I’m very happy with what I got. I still need the PTO/solenoid wiring harness. Additionally all the rollers need new needle bearings which I need to track down.
  12. W

    What have you done to your FMTV or LMTV today

    So as far as lifting the winch into position I cheated. I used my pallet forks on my tractor. I just slid the forks together, about 12” or so apart? Then lifted it by cradling the winch drum. That made it real easy to adjust the frame to align the bolt holes. Once one bolt was in it was very...
  13. W

    What have you done to your FMTV or LMTV today

    Nice! I managed to get mine hung too, got all the guides on and the hydraulic tank fender. PTO is next for me when I get some time.
  14. W

    Need help finding correct wiring pins

    Excellent! Copy all, will do. Thanks for the quick reply.
  15. W

    Need help finding correct wiring pins

    Well it’s the winch harness. So it plugs in under the dashboard I believe with the white connector blocks, those are in good shape. But these black blocks would terminate somewhere under the fuse panel, where? I don’t know yet. M1078A1 A-T021157EFHL , not too sure on those last two letters...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks