70deuce
Active member
- 936
- 122
- 43
- Location
- Franktown, CO
See link to a PDF file for the steering wheel puller I came with and used on my M37 that worked pretty good.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Steering Wheel Puller That Worked and Did Not Destroy the Wheel
- Thread starter 70deuce
- Start date
- 8,293
- 696
- 113
- Location
- Corpus Christi, TX
Excellent info. I have these puller sets and need to pull my steering wheel soon. Definately information folks can use.
Happyland1410
Member
- 430
- 5
- 18
- Location
- Ada, Oklahoma
I recently replaced the steering wheels on my deuce and on my fire department's M35A3. I found one of the "official" tools but I had been researching other options as well. For others looking into this here are some options. Your method looks like a good one.
http://www.steelsoldiers.com/showthr...g-wheel-puller
http://www.steelsoldiers.com/showthr...l=1#post990848
http://www.stovebolt.com/techtips/steeringwheel.htm
http://www.steelsoldiers.com/showthr...g-wheel-puller
http://www.steelsoldiers.com/showthr...l=1#post990848
http://www.stovebolt.com/techtips/steeringwheel.htm
Attachments
steelandcanvas
Well-known member
- 6,187
- 87
- 48
- Location
- Southwestern Idaho
Great article PC, I'll put it in the Club Newsletter for those that don't frequent this site.
archmark
Member
- 267
- 20
- 18
- Location
- Woodway, TX
Thanks to everyone for the info. Both of my wheels are in pretty bad shaped, which means that they must have been parked with the cabs in direct sunlight most of the time. Surprisingly, the '86 M934 is in just as bad shape as the '66 M185A3. Thanks again...
billyzz
New member
- 211
- 2
- 0
- Location
- rapid city sd
the steering shaft nut is loosened almost all the way
so the wood is pushing on it
i soaked it with penetrating oild and put that thing on
every once in a while i would tighten it more
two days later i heard a noise that sounded like a cross between a bull whip and a gunshot
that thing had popped loose
if i hadnt put the shaft nut back on it would have taken out the rear window.
so the wood is pushing on it
i soaked it with penetrating oild and put that thing on
every once in a while i would tighten it more
two days later i heard a noise that sounded like a cross between a bull whip and a gunshot
that thing had popped loose
if i hadnt put the shaft nut back on it would have taken out the rear window.
billyzz
New member
- 211
- 2
- 0
- Location
- rapid city sd
billyzz
New member
- 211
- 2
- 0
- Location
- rapid city sd
billyzz
New member
- 211
- 2
- 0
- Location
- rapid city sd
Attachments
billyzz
New member
- 211
- 2
- 0
- Location
- rapid city sd
mine cost $1
NormB
Well-known member
- 1,234
- 116
- 63
- Location
- Hampshire, TN
Amazing. I imagine the HMMWV jack with the stud on top would work even better. I'll give it a try.
THANK YOU.
Norm
archmark
Member
- 267
- 20
- 18
- Location
- Woodway, TX
How loud of a "pop" did it make when it finally broke free? When the wheel in my M934 finally broke free, it sounded like a gunshot...
Where can one purchase one just like this?
- 5,718
- 3,125
- 113
- Location
- Metairie/La (N'awlins)
Check with @timntrucks
Thanks.