• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. E

    Opinions on M1009 Tires

    Another vote for Duratracs. They last forever and not much noise. Have them on my 1008 plow and firewood truck and traction never an issue! With that said, I'm looking at Michelin Defender LTX's for another light duty road truck. Great reviews, but pricey. Looks like a snow tire, (but considered...
  2. E

    Finding Belt Size based on Numbers

    See link for Gates info. Once into belts you can see dimensions etc. http://www.gatespowerpro.com/Comergent/en/US/adirect/gates?cmd=catNavigateFrame&CFID=58782514&CFTOKEN=92221324 Had to wait to get the link at work! May not be needed any longer, but good info/resource to have. Eric
  3. E

    CUCV Snow Plow Trucks and Spreaders

    I'm also running the duratracs! I did go larger (285-75-16) but these are terrific tires. Not terribly noisy on the road, and grip like crazy off road or in the snow!!! Bonus, they last really well, downside, pretty pricey (but worth it!) Eric
  4. E

    M1008 Brake line set?

    Buy a 25' roll of nicopp tubing and a flare tool and do it all! The nicopp will not rust and is easy to work with (both flaring and bending) Eric
  5. E

    M1008 front spring replacement help

    Also check ATS springs. They're located in Pa and ship quickly. I use then for the shop I'm at and they're knowledgeable and fairly priced. And they stand behind their products! Eric
  6. E

    CUCV 1986 M1008 - In a Real Pickle - Bad Heads - Need Advice

    Sounds like you already know the direction you're going, but.... New GM small block crate engines are 2-3k, with warranty! Small block requires minimal extra parts and a new convertor. I realize people like the 6.2 for a lot of different reasons, but I'm very happy with the 350 I've had in my...
  7. E

    Passing power with the 4L80E or lack of

    Have had my 1008 for 10 years.... When i got it the PO was in the midst of a gasser conversion. ended up pulling their botched attempted and installed a 350. Mild cam, intake, carb, hei, etc. Installed a tow convertor also. (little higher stall and gas!) Truck always starts and tows reasonably...
  8. E

    How to spot 1028 vs 1008

    Should have the rear spring overload pack and corresponding frame perches
  9. E

    CUCV front spring pictures need opinions on condition

    At shop (and for myself) I've been using ATS spring company out of PA. Bob is extremely knowledgeable and prices and product quality is good. It's becoming increasingly difficult in the automotive industry to find someone who knows, cares and actually sells a decent product! Will be...
  10. E

    New somewhat stock looking tires.

    I have had the duratracs for several years now. Aggressive tread, but not overly noisy on the road. 285-75-16's did rub the drag link, but slight adjustment on the limiter took care of that. Will rub occasionally if overloaded with firewood, (lower fender) but not often enough to worry about...
  11. E

    M1008 Exhaust

    I also used one of the cheap dual kits and must say, quality sucks and they don't fit properly. Right rear tailpipe didn't fit around brake valve and front pipes had to be bent (with our bender) around and cut, etc to make fit. thinner pipe which has also turned to crap quickly. Tailpipes are...
  12. E

    Fuel tank FUBAR

    As stated, available at flaps. (Spectra is the brand). Also can be had cheaper on ebay, but i purchased locally due to concerns with shipping damage. Also will want new straps and new sending unit. Look up as 84 K30 with the diesel....
  13. E

    M1028 disk brake spring?

    Realized it's fixed, but..... Another common issue: When pads are replaced you have to ensure that the pads will slide freely in the grooves(and sliding surfaces clean and greased. Been my experience that low end/cost pads are a little tight while the "1st line"/more expensive pads fit alot...
  14. E

    headlight upgrade

    Definitely recommend the hella assemblies! Personally think the lens optics are much better, and you can than go with better H4's later if desired! I left oe type H4's as the improvement was substantial!
  15. E

    M1009 Speedometer Calibration

    Go to the attached link and look for the Excel application. This is probably the best program I've seen for determining drive/driven gears. Also keep in mind GM has discontinued numerous speedo gears. Guess the TH 400 and 350's are obsolete??? Performance Automatic - SPEEDOMETER GEARS
  16. E

    opinions on 31x10x50 michelin ltxat2's

    I've got the Duratracs on my 1008, mot a lot of miles so far but they seem good! Fairly aggressive, but also not too much road noise.
  17. E

    M1008 Wheel/Tire upgrade

    Just installed 285 75 16 Duratracs on my 08. Despite some of the tirerack reviews I'm very happy with them! The duratracks are a tad taller (33.1) than most of the 285's (32.8). Heve only had a few minor snowfalls this year, but these tires have excellent grip and ride pretty decent for this...
  18. E

    Best source for exhaust?

    Just went through this saga... Towing about 7k behind the truck and a pipe (pre muffler) busted... Motor is a SBC, but pipes are the same! Wasn't able to stay off the gas, loud as ****!!!! Bought the Dynomax system via mail order, but definitely won't recommend as it didn't fit very well! Was...
  19. E

    tires/wheels

    I'm running 285 75 16's on stock rims. Only rubbing was against the drag-link which i fixed by installing/adjusting a longer steering stop bolt in. Tires were Pro comps which wore evenly. Tires were cheap (now 3 yrs old) and fairly aggressive, but are pretty much done. Wanted to put new ones on...
Top