• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. K

    Mep 803

    Do they have to be disconnected to test
  2. K

    Mep 803

    I have been working the s8 and using deoxit going to work that some more. I do have a good working board with the burden resistors that I was thinking of putting on it. But first I will work the heck out of the s8. Might have to put this one on the back burner for a while if that doesn't work. I...
  3. K

    Mep 803

    Not understanding how the engine can trip the overload
  4. K

    Mep 803

    One was not pumping fuel took both out and let them soak for a few days one moved fine the other would not
  5. K

    Mep 803

    Now that is some funny crap
  6. K

    Mep 803

    It is holding around 7200k without tripping overload so I will let it run there for a few hours did add cleaner to tank already. I also have a 802 that I'm in need of a couple of injector pumps if any one has a couple to sell.
  7. K

    Mep 803

    Have am-vm set at 1p l-1 & l-3 and set for110-240 single phase. This is the first one I have had that been a pain in the butt but definitely a good learning experience
  8. K

    Mep 803

    I will try that next. It will hold 10k for a minute or so before the overload fault.
  9. K

    Mep 803

    It does hold 6500k with our any problem it is when I start going over that. Small change in rpms that l adjusted for. The engine doesn't spit out much of any black bits. I have let it run for several hours at 5k without an issue
  10. K

    Mep 803

  11. K

    Mep 803

    The generator is now working and putting out power to the output lugs. But will trip overload when putting 10 kw load on it. Is there anything that needs to be changed when swapping a 802 electrical panel to a 803 everything looks to be the same not sure if I'm missing something.
  12. K

    Mep 803

    I have been going through the wires so far only found 1 and that was on oil pressure gauge. Will continue checking all the wires. Thanks
  13. K

    Mep 803

    Finally had some time to do a little more testing on k20 oil pressure relay pins 7&4 are reading closed with battery disconnect all others are reading correctly. They are all reading correctly with engine running. Really appreciate the help.
  14. K

    Mep 803

    Ok thanks I will check that I was going off a working 802 that has 24 volts at 7&8 on k8 in run position with out engine running. Not sure what's going on there?
  15. K

    Mep 803

    Thanks I will try that next. Question if I have master switch on the run position shouldn't I have 24 volts on terminals 7&8 on k8
  16. K

    Mep 803

    I finally got a chance to look into it a little more to see where I'm losing my 24volts to the battle short switch and thinking the k8 is bad
  17. K

    Mep 803

    The contactor circuit will not function with engine running but it did work before I swapped out the control panels
  18. K

    Mep 803

    The 803 starts and run I have been working on testing everything test fine on battle short with engine off tested a interrupter and checking terminals 5-6 with interrupter held open I'm reading continuity if I remove wires the switch test fine
  19. K

    Mep 803

    Where do I find the -24 tm not to sound stupid but the ones I have do not have much for troubleshooting
  20. K

    Mep 803

    Still working on that. The control panel I put on the 803 was off a low hour reset machine and the control panel looked very nice with nothing missing so I was hoping that there wasn't going to be any problems. Have gone through pretty much all of the wiring everything seems to be in the right...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks