Search results

Howdy, I would plan ahead with as much information as possible. Your a long way from home. You do not know the actual shape of the bearings and grease. The pintle eye on the trailer really cannot be reversed. (it can but it causes other problems, no surge brakes) The M1101 trailers sit high...

Howdy, There are lots of ways to make the connection. The most important is that some disconnect is there. A transfer switch needs to be the size of your service. They kinda get pricey being you need 200amp transfer switch with 200amp service. A interlock work with your current service...

Howdy, I would suggest you look at all the factors of the unknown. 1. if batteries are present, trickle change them fully. If not, buy new batteries and charge them before use. 2. look over all lines, fuel, fuel return, wiring etc.. 3. open air filter and at least blow out, maybe replace if...

Sounds like a job opening that needs to be filled.

Howdy, I think I need to run mine again. I had (far left(closest to fan)) 540 deg next one over 594 deg, next one 590 deg, and last one 538 deg

Howdy, I see its a 2009 model. It has LED lights. It was after 2006 when they were changed to using the LED lights. My trailer was delivered 10/06 and has all incandescent. This is my trailer; All the bulbs are standard incandescent. So swap out the bulbs for the 12v counterparts for a...

Howdy, Just a note. The M1101 trailers are all aluminum, bring zip ties if your doing other lights. I see you have a 12v civi to 24v mil connector. Just be prepared when things do not work and you do not have all your tools and stuff. wires might be clipped, bulbs out etc... Since you are...

Howdy, I was wondering the same thing. Wow, 35 802 units up at auction. Then I saw all the reserve statements, and bids with reserve not met. Some of the units would not qualify for a bid higher than $500. It seems like it was only the Letterkenny units too.

Howdy, I have taken my 2007 Fermont MEP-803A to around 16.5kw load. It just kept chugging along. I would throw some spikes at it, and it would really bellow some smoke, but would keep running. I did this under 120/240 single phase with a surplus load bank. The forum post is at Acquired a...

Howdy, I would suggest you purchase a ground rod, and drive it into the ground where you will have the generator sitting when you want to use it. Yes, your generator will then be a separately derived system and needs to be grounded. Then run your extension cords to where you need.

Howdy, I would suggest getting a electrician out to your place. Your configuration sounds like mine, and I do not think you could explain enough here to have anywhere as a complete correct answer (internet answers are iffy) Grounding is important for you and equipment. note: due to...

Howdy, Am I missing something.. On the MEP-802 and MEP-803 the bonding copper piece is right in plain view whether its bonded or not. The copper piece is a bridge between the Ground and Neutral lugs.

Howdy, The manual. NSN 4720-01-483-6467 part N20353.5 HOSE,NONMETALLIC Name Value CROSS-SECTIONAL SHAPE STYLE ROUND INSIDE DIAMETER 3.5 MILLIMETERS NOMINAL LAYER COMPOSITION AND LOCATION OUTER LAYER BRAIDED COTTON CORD INSIDE SURFACE CONDITION SMOOTH SPECIAL FEATURES COMES IN A...

Howdy, PU-798A High Mobility Power Unit, Silver Eagle LTT-TQG, with MEP-803A 10kw TQG

Howdy, Looking for some confirmation about what should the exhaust manifold temps be? MEP-803A, the inner 2 ports are obviously higher than the outer ports. What is your sustained temp? In example, running at least 30 minutes with a load of 50% or greater, what temp do you have for the...

Howdy, Most (guessing here) European diesel engines use the same stuff. Volkswagen 3.5mm ID fuel hose Mercedes 3.5mm ID fuel hose, and I am sure there are others. This is the name I found it under; Mercedes VW Diesel Fuel Injector Cloth Braid Hose 3.5mm ID

Howdy, Both MEP-802A and MEP-803A series fuel return line is 3.5mm ID and total usage is about 10 feet. NSN 4720-01-483-6467 part N20353.5 HOSE,NONMETALLIC The manual just calls to make from bulk 503-1052. The only thing which I would suggest is the best grade of fuel line which you want to...

Howdy, I was not so much as asking what else I should carry. I was looking at items which were issued at the time the generator was delivered. From information I can find, I am missing a 8lb hammer. I also need to find 3 more ground rod connection knuckles. ****************************** I...

Howdy, I have most of the accessories for my PU-798A (Mep-803a on a LTT-HC high mobility) Pictured; slide hammer slide rod driver/puller rod, with rod knuckle ground rod clamps remote 55gal/5gal fuel pickup adapter aux fuel supply line 6awg braided copper ground carbon dioxide fire...

2007 Fermont MEP-803A Essex A427 load bank 120/240 single phase The pictures are in order of each load applied and what the meter reading was. 3kw load 6kw load 9kw load 12kw load 12kw+3kw load 12kw+3kw+add 1.5kw variable load to 133%