Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.
These two screen shots are the only place I can find a part number for the on and on line lights on the sync box. I had one wire break off then touch the other side and cause a short and burn up the bulb. The box has spares but they are almost all beat up. I've searched with the part number...
Hello .
So one of the 802s I got needs mounts. I did buy one off ebay. It's not the exact same part number. It's -2. I purchased it by gen not part numbers. I'm learning. Anyway the front and rear isolators on the left are cracked bad. I can't seem to find and front ones anywhere. I'm...
I looked back through titles trying to see if this has been addressed. The TM 9-6115-642-24
2-34.2 it says to test the resistors disconnect the battery cable then start testing each resistor. When I had checked them before I assumed they were in parallel with something and that's why they were...
So a while back I had posted about my low fuel float not consistently working. The nice thing on these is open is good so unplugging the floats means you can run. I hadn't been needing the gen anyway but it's nice to know.
I ordered a new float set up from liquid level and received it and put...
Hello. I finally have time to tinker with all the gens I bought. So the 831A runs nice and holds load up to about 2kw. At 2kw it acts like my 803 at 10kw. It holds it and smokes just a tiny bit. When I add say 500 watts it starts smoking pretty good and doesn't like it. If I try 3kw black...
These really are a good design. I got this tank and obviously a Gen or two. I am trying to figure out the best configuration so I have this tank and gen together on a trailer or possibly two trailers but I like the idea of pulling up setting the trailer and having power for days. I like that...
Hello. So I had bought a Gen (power plant 803A) with only 2 hours on the rebuilds and even have the chart showing what those two hours were from. Any way I've read quite a bit and even the green tag says to change at 100 hours. My question is would you still run up to the 100 hours on the same...
Hello.
I did end up getting an 831A and the inverter even works. Rats had lived in it and chewed through the fuel pump wire and were making nest material from the insulation but really not bad shape once cleaned up. My question is about the voltage meter. This one peggs all the way to the...
Hello. I bought a load bank from the auction and it didn't have any part numbers and they conveniently didn't take any pics of the big 400hz stickers on it. I've since gotten my hands on the nsn. Here it isNSN 6150-01-486-6937
I still can't find any info about the thing except that it's a load...
I will be driving from NM to Penn with a 40 foot trailer and only about 10 feet of deck used around may 5th and returning the next weekend with only about 20 feet used up. I thought about renting a smaller trailer but I need the whole 8 foot wide deck and the trailers around me I can rent only...
Hello guys. Well I've continued with my new addiction. I bid on an 831A. My mistake it was an 832. Oops. I got it really cheap so no matter what it doesn't hurt much. Even if all I got was the engine out of the deal I would be happy. My question is is the inverter the only thing making it 400hz...
I have been looking through some of these TMs and they are awesome but I am struggling to find a good list of what is wired to where in this plug. I ran across one post where Guyfang told someone to test from pin.. to gnd and check the reading. I am not looking to solve a particular problem...
Hello I have an 802A I recently acquired and it seems to run decent but there is a lot of fuel I guess all over the engine compartment. ( please bear with me on this since I don't have a sense of smell fuel and oil ect are all very similar to me when there is just a fine coating) I haven't seen...
Hello. I hope I'm doing this correctly. Is this a new thread labeled mep 803a?
I just got home with one of these. Can someone tell me the name and size of the nipple that the water line ties to behind the alternator? I'll post some picks. The nipple is broke off and someone had stuck an ear...
Hello. Does anyone know where I can find the float switch for this machine. Here's why maybe somebody has insight and I don't really need one. When I turn the switch to run the no fuel light comes on and it won't stay running. Heck it won't start if I wait a second for the light to come on. It...