Search results

Short Story Truck was jacked up by tire repair company and it came off the blocks and bent the left front brake dust cover. The TM shows a two piece dust cover. Mine are a One piece dust cover. Any help would be appreciated.

It's Bendix 5007510. Looking for a spare. Found one on line but it's quit high in price. It's the one in front of the crank harmonic balancer mounted in the frame. Some told me that there is a plastic ball in it and when the ball comes apart the failure causes all the air to dump out of the...

On the front of tank there is a pressure sensor for the CTIS on one side. In the middle is a pressure regulating valve. On the other side is the CTIS supply to the valve in the cab. They are all connected to the Wet Tank by a quad fitting. What does the middle pressure regulating valve and line...

I am new to the M932A2 I just bought. I have the TM's and have been looking through them but it is not clear where to unhook and plug the CTIS system from which air tank source. I assume there is a connection for the air to the lines going to the system feeding the tires and another to the valve...

Is there a manufactured cross over pipe? I have searched threads here and missed it if it is there. Thanks in advance!

I thought I purchased an older Engine since it was normally aspirated. It came from a Humvee. Low mileage. I read that the older GEP 6.5 oil pans would work in a CUCV and the newer ones will not. Well, the engine I have is a 12555506, 07 02 K, with double triangles making a diamond on the top...

6.5NA replacing 6.2 M1009 The 24 volt IP solenoids Shut off and Cold start advance under the cover need to be changed to 12 volt. I get that. Do the 12 volt ones for the 6.2 work? There is no external high Idle solenoid on the 6.5 for cold temps. No wiring or hole to bolt it on the bracket. It...

6.5NA hummer engine in M1009 I just bought a NA 6.5 Hummer engine, I haven't received it yet. I have some questions too. My M1009 is 12v with a passenger side Alt. I know the water pump has to be changed if the 6.5 has a serpentine belt so I can use my V belt set up. I read the temp/oil/...

Since the military is getting rid of the Humvee are there some surplus rebuilt engines out there. I want to replace my 6.2 with a 6.5 GEP converted to normally aspirated after it fails. Thought I would look for a deal and put it away for the future. I have looked but don't seem to see any. I...

I rebuilt the front axle. I did a dumb thing. I took my old brake calipers in for core trade and picked up rebuilt ones at O'Reilly's. Due to weather I didn't get to put the new ones on for a couple of day's. They don't fit. My originals are gone. I am screwed. 1984 K5 Blazer ones. Here are some...

I can't find a picture of which way these go. All I had when I took these apart was part of the big seal. No spacer washer on either axle. Found them on Ebay, so now will have the washer/spacer. I know the order they go from the manuals but which side goes towards the knuckle?

This truck is driving me Crazy. As soon as I fix one thing it's something else. It has always started well. I did a 12 volt conversion and had some electrical problems that I fixed with help here. The new starter turns it over better than the old one. It was a little hard starting in that it...

I have a new 12volt volt meter. Tried using the original connections after the rosscommon conversion. Doesn't work no power to the Gray wire. Would like to get this working properly. Can anyone help?

Just finished converting to 12 Volt with new passenger side alternator and two batteries connected together. Put in new glow plugs AC60's and new NAPA Glow plug relay. Also did the Doghead starter relay replacement. Followed the instructions exactly. New starter turns over better than the old 24...

TM 9-2320-289-20 page 7-22 appears to show the Power brake bracket (11) goes on after the master cylinder is placed on the Hydro boost followed by the nuts. I have to replace my Master Cylinder. My 84 M1009 as well as a friends 85 M1009 have the bracket between the Master cylinder and the Hydro...

will it hurt something if I cut this off under the dash after the attached cards and cap it off?

I just got a 1984 M1009. I need the throttle cable and all the connectors/clips/eyelets etc. associated with it. I have looked everywhere on line with no luck. Sounds like the aftermarkets don't fit right.

Roscommon Conversion Question This is well written, But? Step 9 has you disconnect the two alternators from the 12 volt junction block. On the single Alternator option how does the Alternator connect and still charge the system? I assume it is connected some place else in the system.