• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Search results

  1. grendel

    MRAP wheels on 5 ton?

    Do you know how long of a wheel stud was needed for both rims in the rear?
  2. grendel

    WC53 sheet metal

    Is there any place for patch panels, etc?
  3. grendel

    Wrecker power divider propeller shaft CV joint failure.

    It's a 12 spline, small CV. I checked with my place, brought them the CV itself and no, they could not do it. Now bringing them the entire truck, will set it up to use modern CV shafts in a 32 spline variant. I found NOS CV's... for $900.00 +
  4. grendel

    Wrecker bed modification

    Nice thread,
  5. grendel

    Wrecker power divider propeller shaft CV joint failure.

    Sorry for the thread necro, but starting to think about a pony motor to replace the upper CV that let go on the two piece shaft on this M816 sitting here. Did anyone find a replacement part number?
  6. grendel

    MTVR RECOVERY from Yermo cali to Georgia

    So, you want to do this drive again? Yer nutz, but you may be my guy.
  7. grendel

    Wedge front brakes - S cam rear?

    So, after having a few M939A2 series... how are the Wedge front brakes on this? I have some Axletech 4K's from an MRAP. They have air disk brakes. Seems like a no-brainer to me. Thoughts?
  8. grendel

    Drive MTVR MK23 and M322 from San Jose CA to Boston, MA

    Google reports 4,094 miles at 5MPG. 818.8g of Diesel. So roughly 2535.00 in fuel at 3.10 a gallon? Say 200 in tolls...
  9. grendel

    Drive MTVR MK23 and M322 from San Jose CA to Boston, MA

    yeah, that doesn't work well... but add a wrecker/crane/forklift to the ass end and it's all goodness... and air up the rear suspension. Like I said, getting the Pete on or off isn't an issue. We can pick it completely up if need be.
  10. grendel

    Drive MTVR MK23 and M322 from San Jose CA to Boston, MA

    You're reading it right. Already had the Pete on an M322. It's no where stock, much smaller tires for this drive. The driver isn't alone in loading and there are many things like forklifts available. M715 with the windshield down and top in the bed isn't higher than the Pete cab.
  11. grendel

    Drive MTVR MK23 and M322 from San Jose CA to Boston, MA

    The job is to pick up a registered and insured MK23 and M322 (Vet's plates) A stop north of Reno, Nevada and another in Beaumont, TX then home to Boston, MA. Reno: Load a 13K pound 1962 Peterbuilt 282 and a 6K pound 69 Kaiser M715 already on the Pete flatbed on the M322 - Both run very well...
  12. grendel

    J1939 diagnostic code reader. Anyone using it?

    Nice, feel like imaging that machine? :)
  13. grendel

    4L80e and NP241c Upgrade

    looking good Joe.
  14. grendel

    Thoughts on the A/C kit on an M923a2

    I have the hummer in cab unit if you want it.
  15. grendel

    Deuce 4x4 with M105 reduced spring and air bag

    Glad I could help. Why not do a full air ride?
  16. grendel

    MTVR Cost

    I am in the hunt.
  17. grendel

    7.4 Vortec/4L80E with lockers, 39" Baja Projects, trail machine

    More than likely, the ECM for the EFI will run the 4L80E. I am having thoughts about a similiar swap.
  18. grendel

    Rear suspension for 5 ton bob

    I have a complete Pete air ride set up here...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks