• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Search results

  1. M

    Master cylinder kit

    I did a quick search and didn't find it but you can get a rebuild kit for the master cylinder from NAPA. Part number UP175 or from Raybestos. Part number MK175.
  2. M

    Hydraulic Head Plunger Bore Screw Leak

    Mine did the same thing. Loosened and tightened it and it has been fine since. Mine started after I turned up the fuel a little bit. It was fine before.
  3. M

    Indicators flash funny

    Mine started working intermittently or not work at all and it was a bad ground at the flasher.
  4. M

    MEP-017A Starting Problems

    The two inside the control panel? They are 15 amp. They are for the utility outlet.
  5. M

    MEP-017A Battery Voltage Regulator Fuse

    The voltage regulator fuses are SFE 14 amp. They are listed in the engine manual not the generator manual.
  6. M

    Fixed my leaking HH ...woohoo!

    The center bolt on my HH started leaking after I turned up the fuel. I just loosened it and retightened it. No more leak.
  7. M

    Mep-017a mod

    Anyone think it would hurt to hook up a couple of haklogen work lights to it and see if they work?
  8. M

    Mep-017a mod

    Were the mep-017a's ever modified by the military for a 240v neutral mod? I got mine running and checking voltages it has 240 between L2 and L3 in 240v 2 wire single phase but checking further it reads 120 between L0 and L2 and L0 and L3. No neutral mod needed?
  9. M

    Trans lube

    I have seen on here about using 50wt oil in the trans. I can get some 50wt ashless aircraft oil and was wondering if that would be ok to use.
  10. M

    BFR Metals, Salina Kansas, a Goodie Hole

    Any tailgates for a Deuce there?
  11. M

    Can anyone identify this device?

    I think what you have is one of the old home built 24v DC welders. They built them with surplus aircraft generator. http://www.vintageprojects.com/metal-welding/AutoArcWelder.pdf
  12. M

    Exploring the yard.

    OK. Thanks.
  13. M

    Exploring the yard.

    Hello. How about a tailgate for a M35a2?
  14. M

    Air leak

    I replaced it tonight and put ion two remote drain valves while I was at it. The old one is maked 150 psi. Just figured it would be better to replace. Hard to tell how old it is or how worn the spring has gotten.
  15. M

    Air leak

    Sounds good. I already picked one up at the local Tractor Supply. Just have to figure out the easiest way to get to it. Looks like it will be dropping the spare.
  16. M

    Air leak

    Ooops. I meant not over 120 psi for the air system. Need to read these better before I post. I have looked and I can also find one set at 145 psi.
  17. M

    Air leak

    No I haven't. It leaks all of the time. It will bleed off allof the air pressure in about 15 minutes. I can get one for an air compressor that is rated for 125. I would think that should work. The manual just says not over 125 psi.
  18. M

    Air leak

    I have an air leak at the pressure safety valve on my air tanks. Does anyone know what pressure these are rated at? I am thinking I could get one for an air compressor and use it. I haven't dug through the manuals yet to see if it is in there.
  19. M

    MEP-017a 240 plug

    I can lock the cover on the 60A disconnect so no one can mess wwith it.
  20. M

    MEP-017a 240 plug

    I am not backfeeding. I will be hooking up to the lines that feed into the supanel. I will be turning off the 60A breaker that feeds the subpanel.
108,422members
163,719threads
2,303,430posts
733online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks