Search results

Do they close at 95lbs? PM me the cost. I will be working on my truck next week and I will be retesting and might need it if it is still a problem.

replacing pressure switch Where did you get the pressure switch? Part number please?

Quick update on my truck. I picked up my turrent cover , two bows, and 4 H bracket that I had made. Couple of coats of paint and now I am trying to make a gasket for the turret cover by using flex seal. So I made a channel for the liquid to fill and setup. In a couple of days I will know if...

Thanks suprman! Give me a couple of days to get back over to work on it and I will take a picture of the P83 connector. I can see metal around the female holes on the A connector and the B connector but the third hole which I think is the C.

How do I do that. I looked at the governor but not sure were to adjust. I unscrewed the cap and there was a bolt with a nut on it but wasn't sure if that was it. I have been searching the TMs but I haven't found the governor adjustment process yet. Any help would be appreciated!

The process continues Update on my truck. I rebuilt my hydraulic pump and got working Sanded and painted my bows before I put on the new cover I bought. I am having a turret cover built out of 1/8 inch steel and two bow supports that I was missing. I purchased LED headlights(still in the box)...

Fixed Hydraulic pump issue Well I took the hydraulic pump back apart to confirm the proper installation of by rebuild parts and looked at the level of hydraulic fluid. I added some more since all the air parts are above the plate and success!! Now on to my CTIS five flashing lights problem...

I want to say I was certain that it was set but I will check tomorrow because I have about four hours to work on the truck. I am going to pull apart the pump again just to confirm that I did everything correctly. Then I will try tracing the lines and switching the lines to see if that works...

Ok, Today I pulled the hydraulic pump, cleaned and replaced the gaskets and seals like previous posts. After a got everything hooked back up it not only didn't work the backup pump stopped working also. I cleaned the resevior too. It was nasty with a fat like substance in the bottom. Just to...

Suprman, what was the cost of the new dryer?

This is what I have figured: You would rap the cord around the top of the backrest and round in a circle reconnecting it to itself. This would keep it from working off under bumpy conditions.

Steve, Here is how I used them. Fold up one troop seat. Take the Long ends that are equal length and slide it on to the bottom of the backrest with the shorter end facing you. Then slide the H block between the folded seat and the backrest. I am actually looking for two and rubberized...

picture of H block Here is a picture of the H blocks that slide in between the seat and the rail.

They were talking about using it as an anti-spall coating. In other words to help contain the fragments that happen when the bullet hits the steel plate. I have included a quote from AR500 armor that has a coating like Linex. "Our lightweight level IIIA steel plate comes standard with a build...

Thanks Suprman and Tennmogger for your advice and counsel!! The list of things to do the next time I work on the truck keeps growing. ;-)

Wet Tank noise I am uploading a video of a noise that is coming from the wet tank when the truck is off but there is still pressure in the tank. When I opened the drain valve it stop for about five to ten seconds and then restarted. Does anyone have an idea of if this is normal?

Ok, since this thread is about 5 lights flashing on the CTIS. I started to follow the TMs and got didn't get continuity on the socket A of the P84 connector and it says " Repair wire 3032 from connector P84 socket A to terminal lug TL85 (para 2-40) or replace start and charging cable assembly...

I like your solution! Did you cut it 48 inches diameter or something else? I was trying to measure my cab flange but I cam up with 49. Sorry for the late post I just got mine.

On a side note, I need a cargo cover for my LMTV. I would prefer the 3 color camo but the stuff I am finding is really expensive. What is a good source or average price for a cover? I have the metal frame. I am seriously thinking about finding a small boat cover place and getting them to...

Checked the hydro fluid level and added some but still no luck on raising the cab. I used the manual pump and raised the cab so I guess that means I have a pump(rebuild) issue. On the CTIS the 5 lights are flashing from the beginning not just after the initial pressure test. Didn't have time...