• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. Larch

    IP fuel shutoff rod

    Started the truck the other day and all was fine. I haven't started it in a number of years. The shut off rod was so gummed up, it was hard to move it with a screw driver. I removed it and cleaned it up to move freely and reassembled. Put batteries in and it started up fairly quickly and ran...
  2. Larch

    IP fuel shutoff rod

    Thanks for the reply. I'll have a board ready for the air intake when I start it. Thanks again!
  3. Larch

    IP fuel shutoff rod

    I had a sticky fuel shut off rod so I removed it and cleaned it (yes I used the sticky, Thanks). The question I have is when replacing the shut off rod- Can the shut off rod be in the wrong position if the rod sits flush with the housing? while trying to replace the rod I felt like it was in...
  4. Larch

    snow plow frame

    Try giving him a phone call.
  5. Larch

    snow plow frame

    Check out this link www.jatonkam35s.com/specialtywork.htm
  6. Larch

    cucv starts, runs rough, excessive smoke then dies 2-5 min

    How did you bypass the temp sensor? Did you just connect the two wires together?
  7. Larch

    M1008 will run and then shut off

    Some people have removed that sensor and plugged the hole with a bolt.
  8. Larch

    Troubleshooting: M1009 - Replaced IP, Now running slow

    So what was wrong with it? What did the new mechanic do to get it running right?
  9. Larch

    CUCV M1028 Tach Assistance

    Look into a tach called "Tiny tach" easy to install.
  10. Larch

    Illustration for Catalog 52D?

    The illustrations start on page 286.
  11. Larch

    Gauges: Tach, temp, and others. Recommendations?

    truck1, do you have a picture of where you installed your tiny tach?
  12. Larch

    Oil pressure light and 4 Wheel drive light not working

    I found my problem. I removed the instrument cluster to clean the printed circuit and when reinstalling the #4 and #5 contacts were touching, causing the fuse to blow. All dash lights now working.
  13. Larch

    Oil pressure light and 4 Wheel drive light not working

    I have a new to me 1028. I have been trying to get all the issues repaired. The oil pressure light does not come on at start up. With the truck running I shift the transfer case into 4 wheel drive and the Gen 1 light gets bright and blows a fuse (accessories 20 amp). I have cleaned up the...
  14. Larch

    Relay questions

    This may help you. This picture came off this site. I'll try again, the picture didn't attach.
  15. Larch

    Cutting/Siping 11.00R20.00 NDT's

    Another picture.
  16. Larch

    Cutting/Siping 11.00R20.00 NDT's

    Some one one this site did these some time ago.
  17. Larch

    M1008 brake master cylinder

    This one may work- Dorman M39435 Brake Master Cylinder
  18. Larch

    M1008 brake master cylinder

    What I found on 20-P. There are 2 different ones listed. #30 is part # 2232073 and part #34 is 2232072. When I used those part #'s to try to find the part I couldn't find that part for sale. I hope this may help you.
  19. Larch

    Starter support bracket?

    Look at this thread it may help you. http://www.steelsoldiers.com/showthread.php?117619-Cucv-starter-bracket/page2&highlight=starter+bracket Sorry that was the direct drive bracket.
  20. Larch

    Cucv starter bracket.

    I'm also looking for one if anyone has an extra for a direct drive starter.
Top