• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. K

    M1009 Harmonic balancer

    > I must be the luckiest CUCV owner alive. After owning many, many CUCV's I have never replaced a harmonic balancer on any of the CUCV's I owned. I never replaced one on any vehicle I owned. I had vehicles from the 60's that had the original balancers on them. I am a firm believer in "if it...
  2. K

    M1009 Harmonic balancer

    > You don't specifically need a $500 Fluidampr. Any new harmonic balancer will extend the life of your engine. Summit has new Dorman balancers for under $100. Replacing the old harmonic balancer should be the absolute first thing you should do to extend the life of your engine. Just my 2 cents...
  3. K

    M1009 Harmonic balancer

    I've read some horror stories of the stock Harmonic balancers coming apart on the 6.2L's and destroying engines. (Rubber coming apart, etc) I've got no projects planned for my M1009 at the moment.. would a new fluidampr be a good investment? They're kinda pricey, so it would take a lot of...
  4. K

    Tips to strip the top battery brackets?

    It crossed my mind to just throw it into a burn pile... it's not load bearing or anything. In theory I could quench it and sharpen it too :lol:
  5. K

    Tips to strip the top battery brackets?

    oof. ok. I was a bit naive thinking I could just peel + scrape it of it off and maybe torch any remaining bits. I'll plan to give them both a soak.
  6. K

    Tips to strip the top battery brackets?

    Anyone out there have tips to strip off the rubber / plastic coating on the top battery brackets on the M1009? They're peeling + rusting at the edges. I'm swapping the batteries and wanted to take a quick crack at repainting the tops with self-etch and giving them a cheap rubber bed-liner...
  7. K

    High flow fill neck - fuel truck end?

    Ah. Thanks for filling in the gap here. Was trying to figure out standard names to see if we could locate caps not tied to the CUCV via part numbers / etc. I've seen folks mentioning the CUCV could be tanker-filled with the "extremely high volume" filler neck (at least triple a semi-truck...
  8. K

    High flow fill neck - fuel truck end?

    I was poking around looking for a new fuel tank cap for my M1009 (and quickly realizing my current cap with the clogged vent is worth it's weight in gold) and stumbled across a military fuel truck nozzle on eBay... It kind of looks "correct". (The end is a clamp which would seemingly...
  9. K

    What have you done to your CUCV today/lately - Part 2

    Been a while since I posted. * Roll on bedliner $69 * Soft top ($900 oof) * Rear tires (dry-rotted, $300) * Change rear diff fluid (a nice shade of black coffee) * Driver + Passenger door cards (~$275) * Driver + Passenger rubber seals Longer Ago: * Transmission fluid changed * All important...
  10. K

    Transfer case shift knob cover

    Eh. I ended up making my own helicoils. (wall diameter too thin) Drilled threaded insert out of new ball, ground the aluminum nut from the stock ball and epoxied it in place. It looks better than the picture. I also "rebuilt" the housing. 1) Remove the 35 year old peanut butter grease 2)...
  11. K

    Transfer case shift knob cover

    Ah. I'm in the process of removing the ancient rubber "carpet" in my M1009 and just noticed these. Thanks for the tip. Plan on extending the bedliner into the drivers area after filling some rust holes in the floor edges. I found the following cheap product on Amazon for the transfer case...
  12. K

    Removing the M1009 rear seatbelt bolts

    Dammit. You're right too often. I checked the temp and I was doing around 300-400F. Got er' up to 500-600F+ and it finally broke loose. "If the undercoating isn't on fire, you're not heating it up enough." I just drilled out the one with the stripped torx... tired of dicking with it lol.
  13. K

    Removing the M1009 rear seatbelt bolts

    "heating (bottom nut)" That was my first goto. :-) PB blaster overnight, propane torch on bottom nut for ~1 - 2 minutes. No movement with breaker bar. These Torx bits will only take so much before they snap. I'll try a bit longer heat on the one not rounded off.
  14. K

    Removing the M1009 rear seatbelt bolts

    Thanks. Drill it is. I'll pick up some new "good" bits and try to drill them out. Man, I hate big Torx. Just use a damn bolt GM
  15. K

    Removing the M1009 rear seatbelt bolts

    Anyone have any magic woo-woo tricks to remove the rear T50 seatbolt belts in the M1009? Wanted to apply bedliner to the back-half and they seem "permanent" lol I've been PB-blastin (top + bottom), heating (bottom nut), beating, PB-blastin (top + bottom), heating (bottom nut), beating for a...
  16. K

    Firewall 12v connection current limits?

    Eh. I wasn't doing a relay since 5-7A isn't *that* much... but yeah, I could switch the relay off of the 12v point the radio is connected to, then feed the light bar 12v or 24v directly from the battery (front or both) via a fused cable. (it's rated up to 30v... but it was pretty cheap so not...
  17. K

    Firewall 12v connection current limits?

    I'm putting a light bar on my M1009, and there is a 12v connection on the firewall that is conveniently switched by the Blackout / Civy light switch. Anyone know the current limits of that circuit? I have a feeling it's where the lighting ties into, so would be the perfect place to power the...
  18. K

    Reviving a parked M1009

    That's my master cylinder from a few years ago as an example of "mixed DOT3/4 + DOT5" Hopefully HeisenBob's master cylinder is better. I fixed mine a few years ago :)
  19. K

    Reviving a parked M1009

    I'd only bother with this is the fluid is *not* normal (aka not clear). If it's clear or mostly clear and is mostly full.. leave it alone and you'll be fine for your journey. If the truck stops fine on hard stops and doesn't swerve or do anything weird, you'll be ok for a single journey. This...
  20. K

    Reviving a parked M1009

    Check your brake fluid. Make sure it's either "all DOT3/4" or "all DOT5". These come with DOT5 which is uncommon enough now-a-days they can easily get "topped up" with DOT3/4 by unknowing mechanics. I drove my "been serviced" M1009 home over a 120Mile butt-hole clenching night journey with...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks