Volvo740turbo
New member
- 281
- 0
- 0
- Location
- St.louis missouri
Of you have a 1008 or 1009 the gp are 12v...
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your CUCV today/lately - Part 2
- Thread starter Warthog
- Start date
Of you have a 1008 or 1009 the gp are 12v...
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
Yes they are 12v.
I think most everyone knew I meant the resistor bypass would not be done.
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
Received notice that the CUCV winter front has already been shipped and will be here Thursday.
Now thats service!
Now thats service!
- 1,965
- 279
- 83
- Location
- Colchester, VT
The other day I changed the plow truck over to a spin on fuel filter setup and installed new rubber fuel lines to the filter as well.
It had recently started leaking fuel out the inspection cover underneath and I was hoping it was a bad rubber hose feeding the injection pump, but a closer look showed it was leaking out the throttle shaft. So today my brother and I took all that apart and changed out the o rings. Not a terrible job and there is plenty of room to do it without pulling the IP. Hopefully the rest of the IP is in better shape.
On another note the engine rebuild tag under the intake manifold says it's bored 0.75 over.
It had recently started leaking fuel out the inspection cover underneath and I was hoping it was a bad rubber hose feeding the injection pump, but a closer look showed it was leaking out the throttle shaft. So today my brother and I took all that apart and changed out the o rings. Not a terrible job and there is plenty of room to do it without pulling the IP. Hopefully the rest of the IP is in better shape.
On another note the engine rebuild tag under the intake manifold says it's bored 0.75 over.
- 1,653
- 1,669
- 113
- Location
- Nova Laboratories, WA
If one O-ring failed, any others that haven't failed won't be far behind.. Kinda like changing headlight bulbs in pairs...
- 1,965
- 279
- 83
- Location
- Colchester, VT
I guess we'll see. That's why I said I hope the rest is in better shape.
computer54
Member
- 317
- 1
- 18
- Location
- Nashville,TN
And this what I have to look forword to do.
cucvrus
Well-known member
- 11,473
- 10,432
- 113
- Location
- Jonestown Pennsylvania
IMHO. Avoid the inevitable. I look at throttle shaft seals like water pump seals. When they start leaking I never changed a water pump seal. And technically you could with a press. Get my point. The end is near. On a truck I depend on for plowing it would fail in the biggest snow storm. That has been my experience with things. GOOD Luck and Happy Holidays.
chief1983
Member
- 290
- 1
- 16
- Location
- Saint Charles, MO
0.75!!!!
cucvrus
Well-known member
- 11,473
- 10,432
- 113
- Location
- Jonestown Pennsylvania
There is not much that can be done to figure out how to write 0.075 as a fraction, except to literally use what the decimal portion of your number, the .075, means. Since there are 3 digits in 075, the very last digit is the "1000th" decimal place. So we can just say that .075 is the same as 075/1000
A normal human hair is approximately 0.003 inch to 0.005 inch in diameter.
That thing is barely bored at all. Not sure you would even notice if you put stock pistons and rings in it. Is it a Tooele rebuild?
A normal human hair is approximately 0.003 inch to 0.005 inch in diameter.
That thing is barely bored at all. Not sure you would even notice if you put stock pistons and rings in it. Is it a Tooele rebuild?
- 1,965
- 279
- 83
- Location
- Colchester, VT
The joke is that it doesn't say .075 it says 0.75, or 3/4". 0.075 would put it at the factory bore for a 6.5 engine.
Yes it is a Tooele "Pride and quality" rebuild. That's one reason I won't put a lot of money into the engine itself, I had another m1028 with one, it didn't last too long and I've never heard a good thing about them.
joshuak
Active member
- 747
- 214
- 43
- Location
- Slower shore, DE
I added rust proofing to my '09s PMCS. Followed the directions in chapter 6 of the Army's TB 43-0213. As a rustproofing compound I used Fluid Film, which I purchased as a kit from here. I upgraded to the pro gun because I wanted the extension wand with 360 nozzle. Used a full gallon, leaving a wet layer of about 3mm thick, sprayed at 80 psi. FF website recommends between 3 and 4 mm.
Drilled or enlarged existing about 16 1/2" holes, which after plugging looked like this:
And a pic. of the rear wheel well.
Drilled or enlarged existing about 16 1/2" holes, which after plugging looked like this:
And a pic. of the rear wheel well.
pigpen60
Active member
- 681
- 127
- 43
- Location
- foley/missouri
So have you used fluid film before?
joshuak
Active member
- 747
- 214
- 43
- Location
- Slower shore, DE
Not in an automotive application. I found a few cans squirreled away at work a few months ago and used them on some cabinets that are exposed to corrosive environment and so far have been happy with the results, doing this made me aware of smell and consistency after applying. Also, I found mostly decent reviews online, so it was worth a chance to me.
- 881
- 521
- 93
- Location
- tucson AZ
I have heard that 5/4 of the population does not understand fractions....
- 867
- 647
- 93
- Location
- Cooperstown NY
That's true, and to make it more confusing, that 5/4 is actually 1-1/16" in the lumber industry.
Last edited:
- 1,505
- 1,676
- 113
- Location
- Puget Sound, WA
ALT + 0188 = ¼
ALT + 0189 = ½
ALT + 0190 = ¾
You have to use the number pad not the row of numbers at the top of the keyboard.
- 623
- 53
- 28
- Location
- Attleboro, MA
Still working out issues on our new M1010, But she looks much better now!
Before
After!
Before
After!
- 888
- 1,321
- 93
- Location
- Rhein-Main Area, Germany
do you have any particular plans with the truck.......... I'm just curious
- 888
- 1,321
- 93
- Location
- Rhein-Main Area, Germany
......and by the way, it Looks great