Sorry if this has been covered already but, i am having trouble identifying the manufacture of the Surge Brake on my M1101 Trailer. I am looking to swap out the Pintle inner slide and replace it with an inner slide with channel . Picture's below . Any help would be greatly appreciated
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Surge Brake ID
- Thread starter 1talian0
- Start date
- 2,974
- 4,355
- 113
- Location
- Olympia/WA
I can't tell you for 100% certain, but several of the internal components are the same part numbers as the Titan Model 6 including the master cylinder and surge damper.
www.crofttrailer.com
EDIT: looking through the parts breakdowns I am not seeing an adjustable height hitch.
40932 --- Hydraulic Brake Actuator with 3" Tow Ring - 8,000 lb Capacity - DX8.0
Croft Trailer Supply is your One-Stop Trailer Shop. Buy trailers, parts and accessories, or have your trailer serviced or repaired by the best in the industry.
www.crofttrailer.com
EDIT: looking through the parts breakdowns I am not seeing an adjustable height hitch.
Last edited:
- 2,974
- 4,355
- 113
- Location
- Olympia/WA
okay, found one on another site
Once again though, I am not 100% certain that this is the actual model/correct part.
Once again though, I am not 100% certain that this is the actual model/correct part.
Awesome thx.
Without knowing the manufacture, but all the holes line up it should work without a problem correct ?
Or are they finicky like that ?
- 2,974
- 4,355
- 113
- Location
- Olympia/WA
the important things are the outside dimensions and hole size/distance, as well as whatever it takes to actually activate the master cylinder.
As the actuator on the inside is the same part number, the holes should match. The back of each (or however you would refer to the end that installs into the outer housing) is basically flat and looks like it just pushes against a flat piece with a rod in it so that shouldn't be an issue either.
That just leaves the outer dimensions. That should be as simple as making a phone call to verify it.
I think the main difference between the one for the M1101/1102 and the commercial model is the military one uses a cast outer housing assembly and only has the holes needed to mount to the trailer, and the commercial model is more universal in mounting and appears to be formed steel.
As the actuator on the inside is the same part number, the holes should match. The back of each (or however you would refer to the end that installs into the outer housing) is basically flat and looks like it just pushes against a flat piece with a rod in it so that shouldn't be an issue either.
That just leaves the outer dimensions. That should be as simple as making a phone call to verify it.
I think the main difference between the one for the M1101/1102 and the commercial model is the military one uses a cast outer housing assembly and only has the holes needed to mount to the trailer, and the commercial model is more universal in mounting and appears to be formed steel.
thanks again for your help
Jeepadict
Well-known member
- 477
- 706
- 93
- Location
- Round Mountain, NV
Good call on the idea, I'm getting ready to do the very same thing to my 101A3. Parts sourced from the manufacturer directly.
If you're unable to find the exact part you want, I've seen many have torched off the Lunette and welded the channel in its place.
Sent from my SM-G970U using Tapatalk
If you're unable to find the exact part you want, I've seen many have torched off the Lunette and welded the channel in its place.
Sent from my SM-G970U using Tapatalk
You can cut the ring off and weld....its cast steel. Mine has a stop bolt to prevent actuation at the end of the ram. I have not finished making my brake lines and wanted a way to lock it out.
There is my ring being put to use on a 1061 tongue extension
There is my ring being put to use on a 1061 tongue extension
Attachments
Good call on the idea, I'm getting ready to do the very same thing to my 101A3. Parts sourced from the manufacturer directly.
If you're unable to find the exact part you want, I've seen many have torched off the Lunette and welded the channel in its place.
Sent from my SM-G970U using Tapatalk
I have seen that as well but figured someone had to make them. smh
Who did you get your parts kit from ?
Jeepadict
Well-known member
- 477
- 706
- 93
- Location
- Round Mountain, NV
Directly from Mendenhall Industries. The owner hooked me up! Unfortunately, the braking/coupler tongue assembly on a 1101/1103 is from a different manufacturer as I understand.
Sent from my SM-G970U using Tapatalk
Jkgts1
New member
- 12
- 0
- 1
- Location
- Moreno valley
Sorry I know this is an old post, but in case others are wanting to know. I was doing this exact thing last year, when I found one that might fit it was a special order. I ended up making my own. The problem with stock channel is the dimensions, 3”x 2.5”. Not really a normal tube size. I got 3” square tube 1/4” wall, chopped 1/2” off of it and welded it back to make my own 3”x2.5”. I also had to get the 2 wheels inside the surge brake machined down so they would slide in my new tube. I cannot remember how much I had to take off, maybe 1/8”, wasn’t much but without a lathe it would have took me forever. It was lots of work. At the time I was not sure if I could weld on the original ring.
- 7,716
- 19,766
- 113
- Location
- Charlotte NC
.
Neat! I have definitely discovered that the magic of being part of this group is somebody who has been there and done that.
Especially somebody with a searchable description. For me the name of what I want to find takes more time than any repair!