- 16,790
- 24,135
- 113
- Location
- Burgkunstadt, Germany
Its located below the control panel.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
MEP003A battery cables
- Thread starter Vic_949
- Start date
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
So I don’t connect that cable on the starter. It’s for charging batteries
- 16,790
- 24,135
- 113
- Location
- Burgkunstadt, Germany
Look at the set. Do you have the slave port? If not, then you do not need to hook up cable # p55y2n. It will not be there.
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
I do have one
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
Do I hook the positive one or negative one?
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
justinn
Active member
- 81
- 211
- 33
- Location
- THE GREAT STATE OF TEXAS
your battery side should look like this pic.... there should also be 2 smaller wires coming from your control box(panel) that hook up to the respective + and - terminals on the starter, then there is the small trigger wire to activate the solenoid. Your other post got deleted and I forgot what I wrote on there, but I will be back to town on Wednesday if they don't get you squared away by then.
Attachments
justinn
Active member
- 81
- 211
- 33
- Location
- THE GREAT STATE OF TEXAS
notice the Negative from the battery goes to the starter body(big body), and the positive goes to the solenoid(small body)
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
So it doesn’t matter witch cable from the slave port to the starter p55y2n
justinn
Active member
- 81
- 211
- 33
- Location
- THE GREAT STATE OF TEXAS
This is how your starter should look.... nothing should be connected to the output wire of the solenoid that goes to the starter except for the starter itself. There are 2 additional wires IIRC that MUST be connected to the solenoid and starter for the + and - to the control box, in Addition to the trigger wire for the solenoid that looks like you had hooked up.
Attachments
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
So that red arrow p
i know that should it be red or black to connect the slave to the starter p55Y2n or the red arrow pointing to the black wire is the p55Y2n?
- 16,790
- 24,135
- 113
- Location
- Burgkunstadt, Germany
J15 is the slave. The pos side of the slave goes to the pos side of BT1. The neg side of the slave goes to the ground stud. There, wire #P55Y24 goer from the ground stud to the starter
Attachments
- 16,790
- 24,135
- 113
- Location
- Burgkunstadt, Germany
OK, got to bail out. Its 01:00 here and its bed time. Good luck, and everyone stay safe!
justinn
Active member
- 81
- 211
- 33
- Location
- THE GREAT STATE OF TEXAS
Give me a second... I am going to use Guy's picture of the back of the starter to help you
- 6,074
- 4,446
- 113
When you figure out which cables are missing let me know and I'll give you a quote for fabricating them. I've got reels of copper cable of all descriptions and a hydraulic crimper.
justinn
Active member
- 81
- 211
- 33
- Location
- THE GREAT STATE OF TEXAS
Please keep in mind that this is all off the top of my head. The slave +(P50K2) can also connect to the BT1+ or the + side on the solenoid(this is how mine is run on the 003a). Hopefully it helps you to differentiate the wires.
Attachments
Vic_949
Member
- 49
- 12
- 8
- Location
- Bakersfield ca
thank you so much this helps alot
- 16,790
- 24,135
- 113
- Location
- Burgkunstadt, Germany
And normally it is hooked to the +side of the solenoid. The schematic is a bit misleading.
- 7,720
- 19,767
- 113
- Location
- Charlotte NC
.
@Vic_949 ,
I think you have gotten a lot of answers - but I don't think we have answered the NATO wiring question that you had when I explained what a Slave Port was for. My apologies.
What you need to know - from the Slave Port:
The single pin that pokes out is the POSITIVE Post
The "sleeve" part of the NATO connector (about 1 1/2 diameter) is the NEGATIVE Contact.
Picture below is of the Slave Cable
This is the NATO Connector that will be on the outside of your generator.
The Center Post = Positive
The ring just under the TI2000-227 numbers will be Negative (Ground)
EDIT: If you need an ADAPTER to convert from single pin to double bin, information is below.
@Vic_949 ,
I think you have gotten a lot of answers - but I don't think we have answered the NATO wiring question that you had when I explained what a Slave Port was for. My apologies.
What you need to know - from the Slave Port:
The single pin that pokes out is the POSITIVE Post
The "sleeve" part of the NATO connector (about 1 1/2 diameter) is the NEGATIVE Contact.
Picture below is of the Slave Cable
This is the NATO Connector that will be on the outside of your generator.
The Center Post = Positive
The ring just under the TI2000-227 numbers will be Negative (Ground)
EDIT: If you need an ADAPTER to convert from single pin to double bin, information is below.
Last edited:
justinn
Active member
- 81
- 211
- 33
- Location
- THE GREAT STATE OF TEXAS
I could be mistaken, but that looks like an 8xx slave port. If memory serves, the 003a is a round 2pin(side by side pins) instead of the round single pin.