• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

The Humvee takes off on its own like if someone flipped the "After Burner" switch.

Tiwaz

Member
Steel Soldiers Supporter
51
31
18
Location
Miami Beach
The problem is that going at a steady speed, say…. 30 mph without changing the pressure applied on the gas pedal, all of a sudden the truck (1151) behaves like if I floored the pedal, it even downshifts on it’s own and takes off, and if I keep the same pressure on the pedal, it reaches about 50 MPH (or more) and it stays there for 10-15 seconds and then it behaves like I removed the foot from the pedal all together and it goes back to normal.
It does this even at 50 MPH the only difference is that it does not downshifts but you still hear the engine revving up and the speed increases substantially.
 

Mogman

Moderator
Staff member
Moderator
Steel Soldiers Supporter
6,925
9,580
113
Location
Papalote, TX
What gets me is the TPS controls the downshift, along with the programming in the TCM.
So how is the TPS creating WOT without the shaft moving and at the same time the internal gov/linkage fails do do its job creating the same WOT condition as the TPS :eek:
Or is the shaft actually moving.....
 

Mogman

Moderator
Staff member
Moderator
Steel Soldiers Supporter
6,925
9,580
113
Location
Papalote, TX
I would inspect the linkage and cable and the accelerator pedal carefully.
Does there seem to be ANY other influence that could be a "precursor" to the event????
 

NDT

Well-known member
Steel Soldiers Supporter
10,457
6,528
113
Location
Camp Wood/LC, TX
What gets me is the TPS controls the downshift, along with the programming in the TCM.
So how is the TPS creating WOT without the shaft moving and at the same time the internal gov/linkage fails do do its job creating the same WOT condition as the TPS :eek:
Or is the shaft actually moving.....
See this scenario is why I was halfway serious about my "animal" remark, the electronic trans won't downshift if the injection pump went to WOT on it's own internally.
 

Autonomy_Lost

Well-known member
687
1,537
93
Location
Pennsylvania
I beleive there is a switch on the accelerator pedal that is activated when the pedal goes "to the floor" and downshifts....maybe that switch is activiating early?
 

Tiwaz

Member
Steel Soldiers Supporter
51
31
18
Location
Miami Beach
What gets me is the TPS controls the downshift, along with the programming in the TCM.
So how is the TPS creating WOT without the shaft moving and at the same time the internal gov/linkage fails do do its job creating the same WOT condition as the TPS :eek:
Or is the shaft actually moving.....
Nothing moving.... (no strange sound.... no mechanical force change at the pedal... no clues)
 

Tiwaz

Member
Steel Soldiers Supporter
51
31
18
Location
Miami Beach
I would inspect the linkage and cable and the accelerator pedal carefully.
Does there seem to be ANY other influence that could be a "precursor" to the event????
Very good question Mogman but the answer is "No", I have carefully examined the "conditions" in which this problem happens and there is no consistency... no "precursor", engine temp (cold or hot) is not a factor, slope (going up hill or down hill) is not a factor (Florida is so damn flat) speed is not a factor, I don't know how to create situations that are unique but maybe I'll try to drive in D instead of overdrive and see if that changes anything .
 

Tiwaz

Member
Steel Soldiers Supporter
51
31
18
Location
Miami Beach
See this scenario is why I was halfway serious about my "animal" remark, the electronic trans won't downshift if the injection pump went to WOT on it's own internally.
I visually inspected the engine compartment and the pedals area but did not see anything out of the ordinary
 

Tiwaz

Member
Steel Soldiers Supporter
51
31
18
Location
Miami Beach
Silly question, have you inspected the throttle return spring next to the TPS, the one that pushes back on the accelerator cable? Should be a double wire spring.View attachment 935149
Hey Thunderbirds thanks a lot for the picture, it really helps A LOT to identify components in the engine compartment especially when you are not familiar with the name and location of engine components. I'll definitely be checking on that as soon as I get back to my Humvee. Thanks again
 

Tiwaz

Member
Steel Soldiers Supporter
51
31
18
Location
Miami Beach
I beleive there is a switch on the accelerator pedal that is activated when the pedal goes "to the floor" and downshifts....maybe that switch is activiating early?
I didn't know about this switch but definitely worth taking a look at it because it would make sense that if that switch has an intermittent contact, it would provoke that reaction. Can you tell me more specifically where that switch is located....?
 

Mogman

Moderator
Staff member
Moderator
Steel Soldiers Supporter
6,925
9,580
113
Location
Papalote, TX
I didn't know about this switch but definitely worth taking a look at it because it would make sense that if that switch has an intermittent contact, it would provoke that reaction. Can you tell me more specifically where that switch is located....?
I think the switch he talks about is only on the 3 speed, the TPS controls all throttle functions to the transmission.
 

REF

Active member
Steel Soldiers Supporter
117
127
43
Location
Porterville Calif
Could the torque converter be unlocking causing the engine to rev up / feels like a downshift ? Possible adj or replace the switch on the brake ?
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks