• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Recent content by EO2NMCB

  1. EO2NMCB

    Mep003a Fuel pumps not working.

    It was a bad ground! Running like a top again.
  2. EO2NMCB

    Mep003a Fuel pumps not working.

    I pulled the battery's from the 003a to put into a mep002a that I was selling. Put two battery's from the tenders into the Mep003a went to prime and run heard a couple of clicks then nothing. So checked battery's one was 12.5v other 8v. So replaced the bad one, now have 25.3v. The glow plugs...
  3. EO2NMCB

    Cleaning contaminated fuel System NHC250

    Question is the fuel passages in the head between injectors, what is the best way to clean them? Sent the fuel tank out for cleaning, it will be a few weeks before I get to all the lines. Just trying to get my ducks in a row.
  4. EO2NMCB

    Fdc bypass on non turdbo... Egt?

    My non turbo makes a ton of smoke with the FDC still working, I think its that way on all non turbo's, as the turbo was only added to clean up some of the smoke.
  5. EO2NMCB

    New to me M936A2 engine idle / load issues

    Any update on the fuel issues?
  6. EO2NMCB

    Resources for identifying low bridges?

    I use the Allstays Truck and travel, it shows all the low bridges.
  7. EO2NMCB

    M931A1 length?

    Back of the cab to pintle I come up with 148" give or take.
  8. EO2NMCB

    a strange noise coming from an NHC250 water pump

    My 927 did, busted in half.
  9. EO2NMCB

    M939a1 stalling

    Truck starts and runs great, however with normal braking it dies. Starts right back up. I unhooked the lock up solenoid for 5th gear on the transmission, made no difference. I shifted in to neutral while beginning to brake, still stalls out. Could the PT pump be causing this as the injectors...
  10. EO2NMCB

    Still not starting or idling

    http://dieselparts.com/ Check with Premco Lamlasas TX. Got a set of rebuilt injectors for a Nhc250, truck starts great and runs like a top now, was 75 per injector, 25 core core charge ea. Simp5782 had told me about them.
  11. EO2NMCB

    M927 no start

    It now starts so easy and sounds great. Thanks for the knowledge Willwager and Simp5782!!!
  12. EO2NMCB

    M927 no start

    So I got rebuilt injectors from Premco, thanks Wes! Now my question doing IBC (Top stop injectors) do I bottom out the injector plus 15* to push the oil out or only set it at 6 in pds? from the TM Turn adjusting screw (2) down until top of plunger (4) contacts cup (5). Advance adjusting screw...
  13. EO2NMCB

    Rebuilt 250 has maxed out oil pressure

    Unless it’s been modified the M809 series trucks have a mechanical gauge.
  14. EO2NMCB

    What have you done to your 5 ton this week?

    Corrected RRAD paint over rust program. Was not near job that I had envisioned. Hood does not shift back and forth when being closed now!
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks