Search results

The Deuces from what i have seen of late are going in the 5 to 10K range for average ones, maybe run ok but need new soft top and some glass and a bit of maintenance. I saw one on FB yesterday the guy was asking 59K for it and when I asked why his was so special of course I got no answer...

First thing I would do is check out the thermostat and make sure its functioning correctly and opening all the way? If that checks out start looking at the cooling lines and radiator, cooling fans etc. Overheating is to my knowledge never a normal situation!

Thanks very much for your assistance in getting the number for this part its greatly appreciated!!!

Hello folks its not very often I need assistance on my trucks but I guess times change. I have a 1988 M977 HEMTT with a General Thermodynamics radiator and I need a radiator cap. I got hold of eastern Surplus this am to order one and they need an NSN or part number so I can place the order. I...

I thought Memphis Equipment had fiberglass ones at one time, I always got lucky and found NOS ones but they may be worth a call?

Mark it could be any of the above issues causing your problem. The first thing I would do is get some air tool oil into the trans manifold assembly then I would disconnect the air line leading the to the shifter assembly and put a decent amount of air tool oil into both these locations, then I...

I have been using Lucas Red and tacky for all my truck wheel bearings since it came out and its always done a very nice job!

Its been awhile but I remember Midwest Military and Vintage power wagon both had them at one time.

I spent an entire day there and it still wasnt enough, it pretty amazing what all they have in there and 100% worth going!

Should be able to find a 230 pretty darned common engine. I have seen just about any and every kind of engine that has been put into an M37. I even believe that Vintage Power wagon has an adapter kit you can buy to replace the 230 with a 318.

Kurtomatic the bottom line here is what are you going to want to use the truck for into the future? If this is something that youe have ideas of a long distance traveler/camper then I would stay away from the Deuce, the reality is that its an old truck and those are the issues your going to...

Welcome to the madness Jay! You are correct the M54 is an old timer with a multi fuel engine and you are always going to wanting more power! If I may make a suggestion that will guaranteed to save you money in the long run and because of a number of reasons primarily I would hate to see you...

It sure sounds like you have an air block very likely in the radiator itself. This is what I would try, open the drain valve on the bottom of the radiator and start filling, are you getting coolant out of the drain valve? If so OK you getting coolant that far. Then I would start loosening...

I had an S280 shelter from this same mfg and found it to be very well build and well put together. The main things on any shelter is look at the roof and inside for signs of leaking water that can do some damage but this shelter is new enough I doubt your going to have any of those issues...

In ND I register all my trucks as FARM VEHICLES and it gets me much cheaper registration and licensing rates but the truck has to be of a certain GVW and the limitations on the truck is that you cannot drive it further than 400 miles from your farm and I believe that it. It looks like you made...

All very good advice for somebody looking for their first MV and a Deuce is an excellent place to start. They are not nearly as big or as intimidating as the 5 ton, they are a fair bit simpler to work on and understand the concepts behind the truck. They get darned near twice the mileage as a...

I generally pull a battery cable on my trucks when I have to park them outside in the public!

Your problem is going to have to do with the float or float height. First are you sure the float is floating? If for some reason the float is cracked or has a hole it will sink and the carb will have gas pouring out of it. Second make sure the float is moving on its shaft that it hinges on...

Karl here and Thanks 98G Where is the transfer case located where it will be picked up at? Is it packed on a standard pallet correctly? What is the weight of the package complete? Where will you be shipping it to, and what unloading facilities are at the destination location? Is the...

If the filters take care of this issue you are good to go, if not then the next step would be the injector on that hole!