Search results

I have a good set of (4) stock size of tires for M1008/M1028 Goodyear AT - LT235 85R16, pic is of the worst one of the lot, more pics if you want them $60 LMTV Troop seats, cast/extruded aluminum. NOS , 2 sections which I think are for one side. I was going to use them on my M818 / Deuce bed...

Latest pic of my "work in progress" Just added the cut down Deuce bed and troop seats Write up soon...

Just cut down a non-dropside bed and it was amazingly fast and accurate with a sawzall and some Milwaukee "Torch" blades, cut an entire bed section out , 2 full cuts of the width of the bed, and only used 3 blades. Take your time, use angle iron as a guide and you will be surprised at the ease...

Changed the oil for the first time last night, HOLY COW that is a LOT of oil! I didn’t think it would ever stop draining out of the filter housing I also found a leak on the brake line inside the frame rail on the driver’s side. Looks like it might be at the connection between the steel line and...

Qty (1) Tan Medium short sleve Qty (1) Black XL short sleve Pick up at rally Thanks!

Need an M818 behind the cab tool box, box only Thanks!

One pin holds the drawbar/lunette to the trailer and the other pin holds the hydraulic damper (looks like a tiny shock absorber) to the drabar / lunette I'll try to paste a pic from the TM I have in the morning ( can't do THAT from the iPad :-D ) I could order from Schutt but was assuming they...

So out of my TM 209-2330-392-14P I need the spec on (2) parts and have searched the internet in vain on the "spec" for these parts. I have the NSN but where do I find out "it's a pin 6" long and half inch in diameter with a hole at the end for a 1/8" cotter pin" Or maybe a drawing of it...

Home safe, pics and action report later

Have my appointment at 0800 this morning to pick up my M1102 trailer at Anniston About a 2 1/2 hour ride Truck is loaded with a few tools and hopefully everything I need. I'm taking a flat bed 16' civy trailer rather than pulling it back since I didn't do an inspection and don't want any...

Need to move a M818 5th wheel and ramps from Atlanta GA area to Albany NY area Let me know if you can help, no particular time frame, we are flexible Thanks!

:funny:

(Squirt-Truck) Oh you KNOW I enjoyed! But let's call a serious moment, my joy pales in comparison to the joy that my dad has every time we take it over to do any work on it. He came with me on the recovery and has been involved every step of the way. I know he has a smile on his face every time...

(Floridianson) Yea... I'm quite the rebel! :-D Hopefully my post wont be deleted because I read the TM but failed to actually follow ALL the steps outlined... We will see... (groundog) Since I did both sides at one time I did a method I found here (don't remember which thread) and used a long...

(F18hornetM) Keep an eye on it, mine was puking pretty bad by the time I got around to changing them, and what a mess it was...

We scratched our heads for a little while wondering if they would clear or not but turning the knuckle all the way to the rear and they just fit over the end Bleeders like everything else on the front end were new, so hopefully when and if I ever have to bleed them the wont be frozen!

Here are the axles out, the closest one was the one with the leaky seal, thin grease The axle splines, not sure if you can see the blue dye or not Blue grease pencil "16.560" drum turned to Clean knuckle housing ready for the new seal New brake shoes! "Soldier B" hard at work cleaning, its hard...

So after the Georgia Rally I realized I didn't just have split front axle boots I had a leaking front axle seal. After you would drive it you had a fist sized glob of redish tin "grease" under the passenger side of the truck. So After hours of searching here, I ordered the parts from White Owl...

I stumbled on this thread looking for the exact same info myself I sent an e-mail to PulseTech Products and there response is below. (My original e-mail to them is at the very bottom and there reply right above it) Based on there response I'm torn on if I want to use it for 12V or not. There...

Congrats! Interesting color though? In the pics anyway...