Search results

Hi all, what oil do you use for the oa331 gas engine?

RE: after an auction closes... I agree, I was bidding on a m35a2 in Las cruces NM. Was in good shape, and to boot, it was a M35 that I drove when I was in that guard unit, but it went too high for me to own!

I was wondering about the T-case , how does one verify that it is in high? obviously I worked the lever, I can go from what I assume is high, to neutral, and verify that the truck is not moving, and then into what I think is low. is there a possibility that it is sticking in low even though it...

Wanted to get all of your opinion on this problem, My M35 1954 Gass Reo was owned by, what's the best term, an idiot somewhere in its life. When I attempted to bring it home last weekend I could not get it to go over 35 mph. The engine was running well, but it had no power. I am trying to track...

i'm once again trying to get my truck home, with no more sucess than usual. The prior owner disconnected the mechanical fuel pump, no problem, it was bad. The electric pump he wired in has WAY to little flow, will run the truck in idle, but has no power. Has anyone replaced this pump with a...

ok, the tear down gets worse :) does anyone know if there is a napa part that corresponds with the rotor for the gas engine?

Does anyone have a source for GAS m35 engine parts? looking for a NOS carb.

Hello everyone, I'm trying to get the turn signals back on my deuce, the person who owned it before me had removed everything remotely related to signaling, so it has been quite the challange. I was wondering if I need a flasher unit in the circut. I am using a "control assembly directional...

I have my Deuce registered in NM, I did it as a horseless carriage, and had no problems. BTW, you do NOT have to mail in your horseless carriage plate application. I got mine at the DMV office, the person working there said that field offices can issue out the plates, but most are too lazy to...

Tom, you are correct the truck is still a gasser, has the original Reo gas engine, runs like a charm

I'm not sure on the bed, but I will be back up there next weekend, if you tell me where to look, I can take more pics

Where are you headed in NM?

Not parked there permenantly, just was stopped for lunch!

I finally got a chance to get some pics of my $400 truck, and got to drive it around a bit as well. Still have not had a chance to get it home, but its in a safe place! MY truck seems to have neither the sprag or air system for engaging the front drive. Its a 1954, and it has an extra lever on...

Does antone have a link to copy of MWO 9-2320-200-35-1 ? I'm trying to install some seatbelts in the truck this weekend, but would like to know the correct way to do it.

Hello everyone, I was poking around my wife's family's ranch and found a stack of MV parts. It is labled Closure Hard top for Truck 3/4 ton4x4 weapons carrier. Part number 7720793 Dated 10/1952. it is complete, all glass except for one small side window, had a rear, doors, and top. What is...

RE: Re: RE: TM 9-8022 back from re-binding Don't worry, there are several pages that now have laminated grease prints :D

I found a copy of TM 9-8022 at a garge sale, for only 75 cents!! the binding was bad, and pages were loose. I took it in to office max, asked them to put it in a comb bind, and while they were at it laminate the cover. Got quote $30 I went to pick it up, the laminated EVERY page! Looks good...

i'm trying to get a mix together for ww2 semi-gloss, is it as simple as having home depot mix up some of the 987 equivalent into semi gloss base paint, or is the color different?

On those policies that have mile restrictions, how do they verify that? not to mention that the odometerin my m35 seems not to work