Search results

I don’t know jack about these PCB (learning fast) but the kds (s3) has a port in the front, what is that used for? I also noticed that they sell new glow plug weirs that are separate from the main harness on eBay. My glow plug wires are integrated into my harness. This KDs s3 box should slap...

Yeah I agree. I’m looking at one on epay but man, they dont give those puppies away. I dont know if I should mortgage My home or sell my leg for that PCB. Of course I’m kidding but nearly $700 for a part? Well that’s just insane in my Opinion.

It happens.

Hello i know this is an older post, but i was wondering where at did you tie into the O.E.M harness? Did you tap into the 575A wire that's coming out of the engine control cannon plug? Thank you

If you could get some pictures.

It's a mounting nut that cam out of its slot during disassembly. No worries it was retrieved and put back where it belongs.

Going to install the ground harness today and put an ohm meter on all glow plugs and go from there. like mentioned before all systems are up and fully operation accept for the glow plugs. No power to the glow plug wires. Anyhow i added some pictures of the inside of my PCB showing all the...

I stand corrected. It just sounds unnatural. Goes to show how much I know about diesel.

Now that’s very Intresting to say the least, but I’m sure that trick isn’t good for the engine? Nevertheless it will come in handy when in a pinch. It reminds me of popping the clutch on a manual transmission when the starter has failed. Some times Tip & Tricks are a God sent.

No I get it. It looks like it is going to need a PCB. I just wanted to do the bypass to make DARN sure it’s the PCB. I’m also new to diesel but its really not much different than gasoline. Both are ICE. Moreover, I know if all for laws (fuel, fire compression and exhaust) are not present the...

So it would be Smart just to run 12 volts to the glow plugs? I don't know. All i know is i don't have any power gong to my Glow plug wires. it was running perfect, then the Next day... no start. It has to be the PCB because I i don't have a Controller or anything else that would stop power...

So does any one know if the Glow Plugs are 12 or 24volts? I search the TM's and Im coming up with the glow plugs are 12 volt but run on a 24 volt system? Nevertheless, My Rig is down again and i have traced the issue down to the fact that I'm not getting power to the glow plug wires. So...

Update! Here's a few pics of the inside of my PCB. Couldn't totally disassemble without major disordering but it looks perfect inside accept the little score mark on the ribbon cable. it appears that i dodged a major bullet! I Sealed earthing back up and reinstalled.

Have Been doing a lot to the Humvee. First, I finally broke down and swapped out my O.E.M headlamps for some LED ones. I think they look Great! A big thanks to Midwest Military equipment. Next I installed my safety switch panel. Look's Bad A$$. I always loved the look and action of these...

Got it done today and thanks fro all the help and input you guys gave, I Just decide to drill the grenade and tap the trigger mechanism and then screwed it onto the shifter. So in short, the whole grenade goes up and down. I just thought it was the easier way to get the job done. I really want...

Yeah i lost power to the start switch which is in line with 11a. It appears that 11a runs into the body cannon plug right where the scorched mark is. I don't think there was very much smoke? As for the brake lights, they are fixed. It was just a bad connection. So for a quick recap. The Rig is...

Good information. Thanks

Finally Found this post again. I seen your work on the external gauges and was wondering if you don't mind I steal your Idea? I already got my gauges. what size was all the piping? I think this project is cleaver and very useful. I did get the correct gauges?

Getting ready to further explore the inside of my PCB for any more damage and going to do a little cleaning any tips on disassemble and reassemble the Box? And yes the batteries will be disconnected in advance.