Search results

Yea, really sucks. Was a ton of labor , and not comfortable labor lol. I used Pensacola fuel injection. I really hope so. I’m getting discouraged.

Update, opened top of pump. Metering valve isn’t snappy at all, stayed were it was put essentially. Everything felt very loose in there. Filled with diesel mechanic in a bottle and let sit over night. Started it and 2% better, still worse than before. Company sending me another pump, and I have...

I’m gonna order it from Home Depot actually. Will be here Tuesday

Thank you very much. I was just reading about sticking metering valves after you mentioned it and the symptoms are a match. What a shame I spend 500 on a rebuild and gotta do this. Ordering diesel mechanic in a bottle because no stores stock on the shelf near me

Also, just to say I have the clear line on the return. And I have solid fuel, no air at all. Could it still be a sticking metering valve. And also, when I take the governor cover off and drain it and fill it with mechanic in a bottle, which is the metering valve and is their a trick to Putting...

I’m using the tank again but verified that the tank wasn’t an issue. Plus. Never stalled once. As soon as I put the reman pump on it’s doing this . I read in another post it was a sticking metering valve. Sucks because I just ordered this pump and has 8/22 stamped into the side. What do the...

I’ve just adjusted the timing on the new injection pump to where it stumbles with the light load advance pushed in and now it seems to start with ease, idles good. But if Its idling, i push that pedal and let it go. It stalls. Every time. Same if I drive. I take off, let go of gas to hit brake...

Yes that’s were I set it initially when I installed the pump. And it runs like crap. Stalls if i goose the pedal. Hard starting. Running worse than the original pump lol

@cucvrus @Keith_J ok here’s an update guys. Don’t think it’s too good. So over the past week I swapped the IP. Finished this morn, cranked it over with loose lines on the injector till I got fuel, tightened the lines up. Timing mark a hair to the driver side. Started it up and held the RPMs up...

Injection pump ordered. Will update when new one is installed. My fingers are crossed

It does not stumble at idle with the pin free. I guess when the pin is sticking it’s causing my issue. I’ll try and look up replacing those pin seals but probably just gonna change the IP

well all this knowledge is most appreciated. So as u can see in video, when I push advance in it stumbles down and idles rougher and lower and I get grey smoke from exhaust….but the button that the lever pushes in sticks in the IP upon release, so I WD40’d It and worked it in and out but it...

@Keith_J so a new IP would solve that. I’m gonna go test the advance right now and I’ll take video….I know the timing looks way off in the pic but yesterday I tried to advance the timing and the pump maxed out in the slots, physically couldn’t turn the pump any more and the lines weren’t...

I will test once I get home. But I believe it does. When jnfirst got truck I tried the advance and it was sticking, but I worked it with some penetrating oil and it’s free Now…. u saying timing may be stuck could be because yesterday I changed IP timing on a big swing; and absolutely no change...

@cucvrus which injection pump model is correct for the 84 m1009. DB 2829- mine is incorrect

beautful. Thank you. And I’ll repeat your message for any future people looking. The correct lift pump is the Delphi CHFP906

Update. Yesterday I tried to advance the timing. I got a chain wrench with a pipe and could only get the pump line almost to the line on the block, no further, so j thought the lines were holding me back or something. So I removed the intake manifold again. after doing that and having a better...

Monday I’ll try a big boy bar , if it doesn’t wanna budge I’ll do the lines

LOL that breaker bar is huge! The one I was usuing is a quarter the size, but I’m afraid I’m gonna break something! I was nervous I’d crack the pump max or the valve cover or the head , whatever I’m prying against…. I was told the fuel lines are what could be holding me back so I was gonna...

@cucvrus here’s a MUCH better video I just took, please let me know what u think thank you https://youtube.com/shorts/RbKu9r-OzS4?feature=share