Search results

Upload a pic of the starter. There has been 4 ways to convert the mule to electric start using the starter mount on the engine bell housing. Remove the starter and connect to a battery and energize to observe if the bendix moves out and turns. 1-Ford starter machined into the original manual...

Carb Intake Air Horn Vibration Pinch Clamps form McMaster-Carr 1-29/32" to 2-1/32" https://www.mcmaster.com/#52545k89/=17bujcs Screw Clamps 1-1/4" to 2-1/4" https://www.mcmaster.com/#standard-hose-clamps/=17d1sbw Intake Manifold to Intake Tubes Vibration Pinch Clamps form McMaster-Carr...

Pull the magneto from the engine and put it in a vise. Remove the top [4 screws]. Disconnect the condenser wire from the points and reattach the coil lead to the points. Make sure the points are clean and bright [400-600 grit wet-dry sandpaper] then contact spray to make sure the points are...

Did you get the engine running correctly? If not then check the following: 1-Compression 110#-125# If one cylinder usually the one furthest from the blower is 0# then pull the valve cover and check the position of the exhaust valve it will be much lower than the intake valve. Rats and mice...

Points are inside the magneto. the points are set at 0.016 Before you pull the mag pull the governor and rotate the engine CCW so not to impulse the mag and it fire accidentally. initial timing is done with the governor removed so you can align the mag and cam gear. locate the V on the mag...

When we hear form heaven it is usually Deity now we have heard from a mortal that crossed over at Mach 2 on his mule. A very interesting tag at the bottom of your posts I had to search and found that it was Churchill's broadcast in french on 21 Oct 1940

Yes a Gear change is possible. But you can only lower the ratio using M274 gears in the A1, A2, A4 and A5 transmission producing a slower top end speed. The M274 transmission can have the higher speed gears installed giving a 10% greater speed at 4000 rpm using the AO53 engine. Ground Speed...

What parts are you looking for? Contact me M40 Adapter used when mounting the AN/TVS-2 onto the 106mm RR

What parts do you need?

I was able to put together the actual kit for the Nite Vision Sight Crew Served Weapons for the M2 Tripod Mounted and 106mm RR with the correct case

Contact me with your AN/TVS-2 night vision scope, right angle adapter or M40 mount needs

25 mph is correct an a way to make it go faster is set the governor top speed higher or mount 27 inch tall tires. The 27 inch tires are about the limit for steering. i mounted 27-8.50 x 15 STG tires on special 15 inch wheels. Speed is not your friend especially in 4 wheel steering with worn tie...

Contact me for your CV Joint needs see me on G503 as muleman7

I will look in my stock and see if I have a set or one. If so I can send it to you to copy. Do not know about the Storage Tubes.

Great looking Mule. Talked with John about tires and he is selling out his stock and not planning on restocking. Summit Racing is selling mule tires [Coker] for $119.00 each with free shipping they also sell the tubes with the correct valve stem [TR15] for $16.00 each. They do not have Denman on...

John is selling out his stock of tires and does not plan on stocking more. Summit Racing through eBay sells a set of 4 for $476.00 with free shipping. These are Coker Tires same as the Denman Tire except they do not say Denman on the side even thought the pic on eBay shows Denman.

Heat does funny things when dealing with Ignition. I found that the coil and condenser are effected by heat causing ignition failure. I would check the condenser. It should hold a charge and have no leakage. If it has slight leakage it is still able to function. But when it gets hot it could...

Heat does funny things when dealing with Ignition. I found that the coil and condenser are effected by heat causing ignition failure. I would check the condenser. It should hold a charge and have no leakage. If it has slight leakage it is still able to function. But when it gets hot it could...

It is my experience that when the hub seal starts to leak it is usually due to the hub bearing starting to fail. To check the hub bearing jack up the mule so the wheels are off the ground Grab the wheel at 12 and 6 o'clock and rock in and out. Do not grab the wheel at 9 and 3 o'clock, movement...