Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.
Hello all,
need a little help. My 1985 m1009 needs a new rear drive shaft and yoke. I am not having any luck finding either. Does anyone know of a source or the civilian parts numbers. Any help would be greatly appreciated.
thanks
tom
Hello All its been some time since I posted. I am having a major brake problem with my deuce. Here is the description.
Start the truck, air alarm goes off. Trucks moves fine. Two, three hits on the brake and the pedal is hard as a rock and the brakes are hard as a rock. The only I can get them...
Does anyone have a rear carrier that they are willing to part with? The only one I can find if for an axle that is not limited slip (civilian) I have a lm1009 I am told it is the part that the ring gear is bolted to. Mine is cracked in several places.
Thanks for any help.
Tom
Well, not out of the woods yet. Turns out that along with the drive shaft and U-Joint, I have a cracked rear gear carrier. Would anyone have one????
I am told it is the part that the gear sits in and the ring clamps to????
It seems that it caused oil to leak to the wheel, locking the wheel on...
thanks all.
I just found one local for $65.00. It is for a m1009. If there is a problem with it I will be back in touch!!
Thanks as always for the help.
Tom
Does anyone have a source for a rear drive shaft for a 1985 CUCV. My U-Joint went on Saturday and the connection at the shaft is mangled.
All the local parts places cannot find one.
Any help would be really appreciated.
Thanks
Tom
Thanks Mike, as always!
I will check the link and then the local rebuild for time.
Good to know that I can get new if I have to.
Thanks for offering yours I have a back up plow, but it is VERY marginal
Tom
It would seem that the left side alternator on my 85 m1009 cucv is dead. With a jump the truck will start but after 5 min all electrical dies or is VERY low.
Garage says to replace or rebuild the left and right at the same time. Any thoughts on which way to go. Also where can I get the...
I have a pallet of parts (700lb) in Port Huron MI. It is a gun ring, legs, cab plate, tow bar and some other minor parts. I got it from Texas, but it has now stalled out. I need it to fet as close to Albany NY as possible.
Any help would be appreciated. Otherwise it is going up for sale...
Got home today with the deuce today after a short run across town. Looked up and found I was missing 1 of my convoy light covers. Argh!!!!!!!!
I went back and retraced my steps only to find it in 1000 pieces.
Does anyone have one or know where I could order one?
Thanks
Tom
Update,
I ran the deuce from 6:30am till 5:00 pm today. This is the first time I have really used it. About 60 mile round trip to the quarry. Made five loads each weighing in around 10,000#. Truck responded very well. Yes, stopping was much slower. I did have on load at 12,000#, I was not...
Quick question. I need to go and get 4 pallets of slate today. My deuce is singled out with 11x20's. It will all be on the road and mild hills.
How much weight is safe and not overloaded
Thanks
Tom
I am not sure if this is a good location or I am out of line listing this here. If it is out of line, please pull it and I apologize.
I need to sell my Kawasaki KFX 700 Quad below please find my description. I will post pictures in the morning...
Sent a PM,
If the rear bumper would fit on my M1009 and you still have it, I would take it. Mine is tweeked on one side and I would like to have the step.
Thanks
Tom